Bedienungsanleitung Onkyo TX-NR696 (Seite 133 von 159) (Englisch)

686254

133

Zoom out

Zoom in

Vorherige Seite

1/159

Nächste Seite

133

Front Panel≫ Rear Panel≫ Remote≫

Contents

≫

Connections

≫

Playback

≫

Setup

≫

6. Multi Zone

 1. Zone 2

Change the settings for Zone 2.

Setting Item Default Value Setting Details

Maximum Volume Off Set the maximum value for Zone 2 to prevent the

volume from becoming too loud. Select a value

from "Off", and "50" to "99".

(When "3. Audio Adjust" - "Volume" - "Volume

Display" is set to "Absolute")

Power On Volume Last Set the Zone 2 volume level of when the unit is

turned on. Select a value from "Last" (Volume level

when the unit was turned off), "Min", "1" to "99"

and "Max". (When "3. Audio Adjust" - "Volume" -

"Volume Display" is set to "Absolute")

• You cannot set a higher value than that of

"Maximum Volume".

 2. Remote Play Zone

Change the settings for remote play.

Setting Item Default Value Setting Details

Remote Play

Zone

Auto When playing with AirPlay or Spotify Connect,

or when using the Music Server function to play

remotely from your PC, you can set whether to play

in the main room (where this unit is located) or in a

separate room (ZONE 2).

"Auto": When the main room input is NET, music

is played in the main room. When the separate

room input is NET and the main room input is other

than NET, then the music is played in the separate

room.

"Main", "Zone 2": Select when limiting the play zone

to a particular room. For example, when playing

only in the separate room, select "Zone 2".

• This function may not work if playback is already

proceeding with the same network function.

7. Miscellaneous

 1. Tuner

Change the frequency step for the tuner.

Setting Item Default Value Setting Details

AM/FM

Frequency Step

(North American

and Taiwanese

models)

10 kHz/0.2 MHz Select a frequency step to suit your residential

area.

Select "10 kHz/0.2 MHz" or "9 kHz/0.05 MHz".

• When this setting is changed, all radio presets

are deleted.

AM Frequency

Step (European,

Australian and

Asian models)

9 kHz Select a frequency step to suit your residential

area.

Select "10 kHz" or "9 kHz".

• When this setting is changed, all radio presets

are deleted.

 2. Remote ID

Change the remote controller ID.

Setting Item Default Value Setting Details

Remote ID 1 If multiple ONKYO products are installed in the

same room, select the ID for the remote control

used with this unit from "1", "2" and "3" to prevent

interference between the unit and other ONKYO

products. After changing the ID on the main unit,

set the same ID on the remote controller as the

main unit with the following procedure.

While pressing and holding the MODE button,

press the following buttons for approx. 3 seconds.

• To change the remote controller ID to "1":

MOVIE/TV

• To change the remote controller ID to "2": MUSIC

• To change the remote controller ID to "3": GAME

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR696 Seite 133

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR696

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info