Bedienungsanleitung Onkyo TX-NR696 (Seite 144 von 159) (Englisch)

686254

144

Zoom out

Zoom in

Vorherige Seite

1/159

Nächste Seite

144

Front Panel≫ Rear Panel≫ Remote≫

Contents

≫

Connections

≫

Playback

≫

Setup

≫

Troubleshooting

 Power

❏ When the power is turned on, "AMP Diag Mode" appears on the display of the main unit.

• The protection circuit function may have operated. If the unit suddenly enters the standby state and "AMP Diag Mode" appears on the display

of the main unit when the power is turned on again, this function is diagnosing whether or not the main unit is malfunctioning or there is an

abnormality with the speaker cable connection. When the diagnosis is complete, the following messages are displayed.

CH SP WIRE

If the unit returns to the normal ON state after "CH SP WIRE" appears on the display, the speaker cable may have been short-

circuited. After setting the power of this unit to standby state, connect the speaker cable again. Twist the wires exposed from the tip of

the speaker cable so that the wires do not stick out of the speaker terminal.

NG:

If the operation has stopped with "NG" displayed on the display, set the power of this unit to standby state immediately and remove the

power plug from the outlet. The unit may be malfunctioning. Consult a dealer.

❏ The unit turns off unexpectedly

• If "5. Hardware" - "Power Management" - "Auto Standby" on the Setup menu is activated, the unit automatically enters the standby mode.

• The protection circuit function may have operated due to an abnormal rise in temperature of the unit. In such a case, the power turns off

repeatedly even if the power is turned on each time. Secure sufcient ventilation space around the unit, wait for a while until the temperature of

the unit decreases. Then, turn the power on again.

WARNING: If smoke, smell or abnormal noise is produced by the unit, unplug the power cord from the outlet immediately, and contact the dealer or

our company's support.

( p131)

 Audio

• Make sure that the speaker setup microphone is no longer connected.

• Conrm that the connection between the output jack on the connected device and the input jack on this unit is correct.

• Make sure that none of the connecting cables are bent, twisted, or damaged.

• If the MUTE indicator on the display blinks, press on the remote controller to cancel muting.

• While headphones are connected to the PHONES jack, no sound is output from the speakers.

• When "4. Source" - "Audio Select" - "PCM Fixed Mode" on the Setup menu is set to "On", audio is not played if signals other than PCM are input.

Change the setting to Off.

Check the following if the problem persists after you have conrmed the above.

❏ No sound from the TV

• Change the input selector on this unit to the position of the terminal to which the TV is connected.

• If the TV does not support the ARC function, along with the connection by an HDMI cable, connect the TV with this unit using a digital optical cable. ( p40)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR696 Seite 144

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR696

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info