Bedienungsanleitung Onkyo TX-NR801 (Seite 82 von 97) (Englisch)

553769

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

Operating Other Manufacturers’ Devices Using

the Remote Controller

The remote controller has three learning functions. One

is entering the pre-programmed code for a remote con-

troller of another manufacturer. Another is the normal

learning function that enables the remote controller to

learn the codes directly from other remote controllers

(See page 86). And the last is a macro learning function

that enables you to program a series of operations into

the remote controller so that the operations can all be

performed at once by pressing one button (See page 88).

By entering a pre-programming code, you can have the

RC-511M remote controller operate a component made

by another manufacturer. The buttons that are used for

operation are given on pages 84-85.

Caution

With some brand’s components, some buttons may not

work correctly. In this case, program the command

directly from the other remote controller normally (See

page 86).

When entering the code of Onkyo DVD players:

There are three SETTING numbers. Choose the SET-

TING number according to how you will be using the

DVD player.

No. 601/613: These codes are for operating the Onkyo

DVD player by pointing the remote controller directly

at it, either because it does not have an terminal, or

it does but you are not connecting it with an cable.

First enter 601 and if it does not operate properly, enter

613.

No. 600: This code is for Onkyo DVD players that have

an terminal that you are connecting to the

TX-NR801/TX-NR801E with an cable. You will

then operate the DVD player by pointing the remote

controller at the remote control sensor on the

TX-NR801/TX-NR801E. You do not need to enter this

code because it is factory preset. However, if the code

has been changed to 601 or 613, then you will need to

change it back to 600.

Learning a Pre-programming Code

VOL

DISPLAY

Buttons that can

be pre-programmed

Numeric keys

SEND/LEARN

indicator

In the table on the next page ﬁnd the 3-

digit number for the manufacturer of the

component that you want to operate.

Turn on the component that you want to

operate (i.e., DVD, satellite tuner, or televi-

sion).

While holding down the MODE button on

the RC-511M that you want to program,

press the DISPLAY button, and then

release both buttons.

The SEND/LEARN indicator lights when the

MODE button is pressed and turns off when the

DISPLAY button is pressed. When the indicator

turns off, release both buttons. The SEND/

LEARN indicator lights again.

Within 30 seconds, enter the 3-digit code.

The SEND/LEARN indicator slowly ﬂashes

twice. If the SEND/LEARN indicator quickly

ﬂashes three times, then either a mistaken 3-digit

code was entered or an incorrect operation was

performed. If this occurs, return to step 3.

Press the button that you programmed

and check if the system operates cor-

rectly.

• If the component does not operate properly,

return to step 3 and repeat the steps above.

• If it still does not operate properly, program the

command directly from the other remote con-

troller normally (See page 86).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR801 Seite 82

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info