Bedienungsanleitung Onkyo TX-NR808 (Seite 50 von 100) (Englisch)

645307

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Note

•If the “Surr Back” setting is set to “None” (➔ 46), this setting

cannot be selected.

•If the “Front High” or “Front Wide” setting is enabled (➔ 46),

this setting is fixed at “Manual”.

DTS

■ Neo:6 Music

Center Image

` 0 to 2

to 5

The DTS Neo:6 Music listening mode creates 6-channel

surround sound from 2-channel stereo sources. With

this setting, you can specify by how much the front left

and right channel output is attenuated in order to create

the center channel.

Setting a value “0” in the middle is set to hear a sound.

Sound is spread in left and right (the outside) so that the

set value is made big. Please adjust by liking.

Audyssey DSX™

■ Soundstage

` –3dB to Reference

to +3dB

With this setting, you can adjust the soundstage when using

Audyssey DSX™.

Note

•If the “Center” setting is set to “None”, or both “Front High”

and “Front Wide” settings are set to “None” (➔ 46), this setting

cannot be selected.

Theater-Dimensional

■ Listening Angle

` Wide

Select if the listening angle is 40 degrees.

` Narrow:

Select if the listening angle is 20 degrees.

With this setting, you can optimize the Theater-Dimen-

sional listening mode by specifying the angle of the

front left and right speakers relative to the listening

position. Ideally, the front left and right speakers should

be equidistant from the listening position and at an

angle close to one of the two available settings.

LFE Level

■ Dolby Digital

, DTS

, Multich PCM, Dolby

TrueHD, DTS-HD Master Audio, DSD

` –QdB, –20dB, –10dB, or 0dB

With these settings, you can set the level of the LFE (Low

Frequency Effects) channel individually for each input

sources.

If you find that low-frequency effects are too loud when

using one of these sources, change the setting to –20 dB or

–Q dB.

Dolby Digital and Dolby Digital Plus sources.

DTS and DTS-HD High Resolution Audio sources.

DSD (Super Audio CD) sources.

Items can be set individually for each input selector.

Main menu Source Setup

Audyssey

When Audyssey MultEQ

Room Correction and Speaker

Setup is complete, the “Equalizer” (➔ 47) will be set to

“Audyssey” and the “Dynamic EQ” will be set to “On”.

■ Dynamic EQ

` Off

Audyssey Dynamic EQ

off.

` On:

Audyssey Dynamic EQ on.

The Dynamic EQ indicator will light (➔ 9).

With Audyssey Dynamic EQ, you can enjoy great

sound even when listening at low volume levels.

Audyssey Dynamic EQ solves the problem of deterio-

rating sound quality as volume is decreased by taking

into account human perception and room acoustics. It

does so by selecting the correct frequency response and

surround volume levels moment-by-moment so that the

content sounds the way it was created at any volume

level — not just at reference level.

Note

• If Pure Audio or Direct listening mode is selected, this setting

cannot be selected.

20°/40°

Front left speaker Front right speaker

Source Setup

Preparation

Press the input selector buttons to select an input source.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR808 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR808

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info