Bedienungsanleitung Onkyo TX-NR808 (Seite 61 von 100) (Englisch)

645307

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

NET/USB

The AV receiver is network-ready, which means you can

hook it up to your home network with a standard Ethernet

cable and enjoy the music files stored on your computer or

media server. If your network is connected to the Internet,

you can also enjoy Internet radio.

Network Requirements

■ Ethernet Network

For best results, a 100Base-TX switched Ethernet network

is recommended. Although it’s possible to play music on a

computer that’s connected to the network wirelessly, play-

back may be unreliable, so wired connections are recom-

mended.

■ Ethernet Router

A router manages the network, routing data and supplying

IP addresses. Your router must support the following:

• NAT (Network Address Translation). NAT allows sev-

eral networked computers to access the Internet simulta-

neously via a single Internet connection. The AV

receiver needs Internet access for Internet radio.

• DHCP (Dynamic Host Configuration Protocol). DHCP

supplies IP addresses to network devices, allowing them

to configure themselves automatically.

• A router with a 100Base-TX switch built-in is recom-

mended.

Some routers have a modem built-in, and some ISPs

require you to use specific routers. Please consult your ISP

or computer dealer if you’re unsure.

■ CAT5 Ethernet cable

Use a shielded CAT5 Ethernet cable (straight-type) to con-

nect the AV receiver to your home network.

■ Internet Access (for Internet radio)

To receive Internet radio, your Ethernet network must

have Internet access. A narrowband Internet connection

(e.g., 56K modem, ISDN) will not provide satisfactory

results, so a broadband connection is strongly recom-

mended (e.g., cable modem, xDSL modem, etc). Please

consult your ISP or computer dealer if you’re unsure.

Note

• To receive Internet radio with the AV receiver, your broadband

Internet connection must be working and able to access the Web.

Consult your ISP if you have any problems with your Internet

connection.

• The AV receiver uses DHCP to configure its network settings

automatically. If you want to configure these settings manually,

see “Network Settings” (➔ 67).

• The AV receiver does not support PPPoE settings, so if you have

a PPPoE-type Internet connection, you must use a PPPoE-com-

patible router.

• Depending on your ISP, you may need to specify a proxy server

to use Internet radio. If your computer is configured to use a

proxy server, use the same settings for the AV receiver (➔ 67).

To connect the AV receiver to your home network, plug

one end of a shielded CAT5 Ethernet cable into the AV

receiver’s ETHERNET port, and plug the other end into a

LAN port on your router or switch.

The following diagram shows how you can connect the

AV receiver to your home network. In this example, it’s

connected to a LAN port on a router, which has a 4-port

100Base-TX switch built-in.

About NET Connecting the AV Receiver

Internet radio

Modem

Router

Computer or media server

LAN/Ethernet port

WAN port

LAN port

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR808 Seite 61

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR808

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info