Bedienungsanleitung Onkyo TX-NR929 (Seite 94 von 160) (Englisch)

517568

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Controlling Other Components

En-94

The AV receiver’s remote controller can learn the

commands of other remote controllers. By

transmitting, for example, the Play command from

your CD player’s remote controller, the supplied

remote controller can learn it and then reproduce the

exact same command when its 1 is pressed in CD

remote mode.

This is useful when some buttons don’t work as

expected though you entered the appropriate remote

control code (➔ page 87).

Note

• The following buttons cannot learn new commands:

8RECEIVER, ALL OFF, MY MOVIE, MY TV, MY MUSIC,

REMOTE MODE, MODE.

• The remote controller can learn approximately 70 to 90

commands, although this will be less if commands that use

a lot of memory are learned.

• Remote controller buttons such as Play, Stop, and Pause

are preprogrammed with commands for controlling Onkyo

CD players, cassette decks, and DVD players. However,

they can learn new commands, and you can restore the

preprogrammed commands at any time by resetting the

remote controller (➔ page 89).

• To overwrite a previously acquired command, repeat this

procedure.

• Depending on the remote controller used, some buttons

may not respond as expected, or the learning process itself

may not be possible.

• Only commands from infrared remote controllers can be

acquired.

• When the remote controller runs out of batteries, all

commands acquired will be lost and will have to be learned

all over again. Therefore, do not discard your other remote

controllers.

■ Deleting Acquired Commands

1. While holding down the REMOTE MODE button

for the mode from which you want to delete a

command, press and hold down 8TV until the

REMOTE MODE button lights (about 3 seconds).

2. Press the REMOTE MODE button or the button

from which you want to delete the command.

The REMOTE MODE button flashes twice.

When you press the REMOTE MODE button, all

commands learned in that mode will be deleted.

Learning Commands

While holding down the REMOTE MODE

button for the mode in which you want to use

the command, press and hold down

8RECEIVER until the REMOTE MODE button

lights (about 3 seconds).

On the supplied remote controller, press the

button to which you want to assign the new

command.

Point the remote controllers at each other,

within about 4 inches (10 cm) apart, and then

press and hold the button whose command

you want to acquire until the REMOTE MODE

button flashes.

8RECEIVER

REMOTE

MODE

If the command is learned successfully, the

REMOTE MODE button flashes twice.

To learn more commands, repeat steps 2 and

Press any REMOTE MODE button when

you’ve finished. The REMOTE MODE button

flashes twice.

Within about

4 inches (10 cm)

Supplied remote

controller

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR929 Seite 94

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR929

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info