Bedienungsanleitung Onkyo TX-RZ710 (Seite 26 von 99) (Englisch)

645298

Zoom out

Zoom in

Vorherige Seite

1/99

Nächste Seite

> Before start > Hookup > Setup >Playback > Part Names > Advanced Manual

Troubleshooting | Appendix

or the ZONE 2 SPEAKER, adjust with VOL+/– on the remote

controller. To control on the main unit, press ZONE 2 and adjust

with the MASTER VOLUME control within 8 seconds.

The information for a connected device can be displayed on the

TV screen in a separate room. Press the button while the

remote controller is in the mode for controlling ZONE 2.

0 Power consumption in standby mode increases when the

multi-zone function is being used.

To turn off the function

Press Í while in the mode for controlling ZONE 2 on the

remote controller.

Playing in ZONE 2 only

If you turn the unit to standby during multi-zone playback,

the Z2 indicator is dimmed and the playback mode is

switched to playback in a separate room only. Setting

ZONE 2 to on while this unit is in standby will also switch

the playback mode to the same setting.

Settings

Settings are required in Initial Setup, "4. Multi Zone Setup"

(



P21) to use the multi-zone feature. When checking the

setting content, refer to the following, press on the

remote controller, and check in the Setup menu that is

displayed.

– When you have connected a TV in the separate room

with an HDMI cable, have you selected "Use" in "1. Input

/Output Assign" – "TV Out/OSD" – "Zone2 HDMI"?

– When you are playing the audio from an AV component

with an HDMI cable in the separate

room

, have you

selected "Use" in "1. Input /Output Assign" – "TV Out/

OSD" – "Zone2 HDMI"?

– When you have connected speakers in a separate room

with speaker cable, have you selected "Zone 2" (or

"Zone 2 A + B") in "2. Speaker" – "Configuration" – "Zone

Speaker"?

– When you have connected a power amplifier in a

separate room with an analog audio cable and you want

to control the volume with this unit, have you selected

"Variable" in "6. Multi Zone" – "Zone 2" – "Output Level"?

Others

To adjust the sound quality

It is possible to enhance or moderate the bass and treble of

front speakers. Press TONE on the main unit several times

to select the desired setting from "Bass" and "Treble", and

turn the TONE dial to adjust.

0 You can also adjust the sound quality of a power

amplifier connected in a separate room. After pressing

ZONE 2 on the main unit, within 8 seconds press TONE

and turn the TONE dial to adjust.

0 This cannot be set if the listening mode is Pure Audio

(European, Australian and Asian models) or Direct.

Quick Menu

By pressing Q on the remote controller during play, you can

adjust frequently used settings, such as the sound quality,

using on-screen menus. Select the item with the cursors of

the remote controller and press ENTER to confirm your

selection. To return to the previous screen, press .

0 You can adjust the sound quality with "Tone". "Other"

includes settings such as "A/V Sync" that allows you to

adjust the audio delay when the video is behind the

audio, "Music Optimizer" that provides better sound

quality for compressed audio, and "HDMI Out" which

allows you to select the HDMI OUT terminal to output

from "MAIN", "SUB", and "MAIN+SUB".

When the unit is operating erratically

Try restarting the unit

Restarting the unit may help it operate more smoothly. To

restart the unit, turn it to standby, and then press Í ON/

STANDBY on the main unit for at least 5 seconds. (The

unit’s settings will be maintained.) If there is no

improvement even after the unit is restarted, try

disconnecting and reconnecting the power cords of the unit

and connected equipment.

Resetting the unit (this resets the unit settings to the

default)

If restarting the unit doesn't fix the problem, resetting the

unit to the status at the time of shipment may solve the

problem. If you reset the unit status, your preferences will

be reset to the defaults. Note them down before the

operation below.

1. While pressing the CBL/SAT input selector button on the

main unit, press Í ON/STANDBY.

2. "Clear" appears on the display and the unit returns to

standby. Do not unplug the power cord until "Clear"

disappears from the display.

To reset the remote controller, while holding down MODE,

press until the remote indicator flash twice (about

3 seconds).

Quick Menu

Tone

Level

AccuEQ

Other

Bass

Treble

BD/DVD

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-RZ710 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-RZ710

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info