Bedienungsanleitung Onkyo TX-RZ710 (Seite 96 von 99) (Englisch)

645298

Zoom out

Zoom in

Vorherige Seite

1/99

Nächste Seite

> Specifications > Settings > Listening Modes > Playback Function > Basic Manual

Troubleshooting | Appendix

Wireless LAN Network

•

Try plugging/unplugging the power supply of wireless

LAN router and the unit, check the wireless LAN router

power-on status, and try reboot of the wireless LAN

router.

Check the following if the above does not fix the problem:

■ Cannot access wireless LAN network

•

The wireless LAN router setting may be switched to

Manual. Return the setting to Auto.

•

Try the manual set-up. The connection may succeed.

•

When the wireless LAN router setting is at stealth mode

(mode to hide the SSID key) or when ANY connection

is off, the SSID is not displayed. Change the setting and

try again.

•

Check that the setting of SSID and encryption (WEP,

etc.) is correct. Make sure the network settings of the

unit is properly set.

•

Connection to an SSID that includes multi-byte

characters is not supported. Name the SSID of the

wireless LAN router using single-byte alphanumeric

characters only and try again.

■ Connected to an SSID different to the SSID selected

•

Some wireless LAN routers allow you to set multiple

SSIDs for one unit. If you use the automatic setting

button on such a router, you may end up connecting

with a different SSID from the SSID you wanted to

connect to. Use the connection method requiring you to

enter a password if this happens.

■ Playback is interrupted and communication does

not work

•

You may not receive radio waves due to bad radio wave

conditions. Shorten the distance from the wireless LAN

access point or remove obstacles to improve visibility,

and try again. Place the unit away from microwave

ovens or other access points. It is recommended to

place the wireless LAN router (access point) and the

unit in the same room.

•

If there is a metallic object near the unit, wireless LAN

connection may not be possible as the metal can effect

on the radio wave.

•

When other wireless LAN devices are used near the

unit, several issues such as interrupted playback

and communication may occur. You can avoid these

issues by changing the channel of your wireless LAN

router. For instructions on changing channels, see the

instruction manual provided with your wireless LAN

router.

Multi-zone function (for compatible models only)

■ Cannot ZONE output audio of external AV

component

•

Depending on the model, input by HDMI cable may

not be supported. Check in "Multi-zone Connection"

in the Basic Manual, and if input by HDMI cable is not

supported, connect using a cable that is supported.

•

The audio from externally connected AV components

can only be output when the audio is analog or 2ch

PCM audio signals. If you have connected the AV

component to this unit with a digital cable, the audio

output of the AV component needs to be set to PCM.

■ Others

•

Settings are required in Initial Setup, "Multi Zone Setup"

to use the multi-zone feature. Check in "Initial Setup" in

the Basic Manual.

•

If the audio signal is from the NET input selector, zone

output is not possible for DSD and Dolby TrueHD audio

signals.

Remote Controller

•

Make sure that the batteries are installed with the

correct polarity.

•

Install new batteries. Do not mix different types of

batteries, or old and new batteries.

•

Make sure that the unit is not subjected to direct

sunshine or inverter-type fluorescent lights. Relocate if

necessary.

•

If the unit is installed in a rack or cabinet with colored-

glass doors or if the doors are closed, the remote

controller may not work reliably.

•

After operating the Multi-zone function (for compatible

models only), the remote controller may have switched

to the mode for operating ZONE output audio. Check

"Multi-zone" in "Playback" in the Basic Manual to switch

the remote controller back to the mode for operating in

the main room.

Display, OSD

■ The display doesn't light

•

The display may go dim while the Dimmer is working,

and may also turn off (for compatible models only).

Press DIMMER button and change the brightness level

of the display.

•

The display is turned off when the Pure Audio (for

compatible models only) listening mode is selected.

Others

■ Strange noises can be heard from the unit

•

If you have connected another unit to the same wall

outlet as this unit, this noise may be an effect from the

other unit. If the symptoms improve by unplugging the

power cord of the other unit, use different wall outlets for

this unit and the other unit.

■ When performing AccuEQ Room Calibration, the

message "Noise Error" appears

•

This can be caused by a malfunction in your speaker

unit. Check if the unit produces normal sounds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-RZ710 Seite 96

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-RZ710

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info