Bedienungsanleitung Onkyo TX-RZ730 (Seite 151 von 174) (Englisch)

686253

151

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

151

Front Panel≫ Rear Panel≫ Remote≫

Contents

≫

Connections

≫

Playback

≫

Setup

≫

Updating the Firmware via Network

• Check that the unit is turned on, and the connection to the Internet is secured.

• Turn o the controller components (PC etc.) connected to the network.

• Stop any playing Internet radio, USB storage device, or server content.

• If the multi-zone function is active, turn it o.

• If "HDMI CEC" is set to "On", set it to "O".

– Press . Next, select "5. Hardware" - "HDMI" and press ENTER, then

select "HDMI CEC" and select "O".

* The descriptions may dier from the actual on-screen displays, however, operations

and functions are the same.

Update

1. Press .

The Setup menu is displayed on the TV screen.

Setup

1. Input/Output Assign

2. Speaker

3. Audio Adjust

4. Source

5. Hardware

6. Multi Zone

7. Miscellaneous

1. TV Out / OSD

2. HDMI Input

3. Video Input

4. Digital Audio Input

5. Analog Audio Input

2. Select "7. Miscellaneous" - "Firmware Update" - "Update via NET" with the

cursors in order, then press ENTER.

Setup

1. Input/Output Assign

2. Speaker

3. Audio Adjust

4. Source

5. Hardware

6. Multi Zone

7. Miscellaneous

1. Tuner

2. Remote ID

3. Firmware Update

4. Initial Setup

5. Lock

• If "Firmware Update" is grayed out and cannot be selected, wait for a while

until it starts up.

• If there is no updatable rmware, "Update via NET" cannot be selected.

3. Press ENTER with "Update" selected, and start update.

• During the update, the TV screen may go black depending on the program

to be updated. In such a case, check the progress on the display of the

unit. The TV screen will remain black until the update is completed and the

power is turned on again.

• When "Completed!" is displayed, the update is complete.

4. Press ON/STANDBY on the main unit to turn the unit into standby mode.

The process is completed, and your rmware is updated to the latest version.

• Do not use on the remote controller.

If an Error Message is Displayed

If an error occurs, "- Error!" is displayed on the display of the unit. (""

represents an alphanumeric character.) Refer to the following descriptions and

check.

Error Code

• -01, -10:

LAN cable not found. Connect the LAN cable properly.

• -02, -03, -04, -05, -06, -11, -13, -14, -16, -17, -18, -20,

-21:

Internet connection error. Check the following:

– Whether the router is turned on

– Whether this unit and the router are connected via the network

Unplug and plug the power cords of this unit and the router. This may solve

the problem. If you are still unable to connect to the Internet, the DNS server

or proxy server may be temporarily down. Check the server operation status

with your Internet service provider.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-RZ730 Seite 151

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-RZ730

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info