Bedienungsanleitung Onkyo TX-RZ810 (Seite 26 von 105) (Englisch)

645296

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

> Before start > Hookup > Setup >Playback > Part Names > Advanced Manual

Troubleshooting | Appendix

0 If ZONE 2 or ZONE 3 is turned on when the listening

mode of the main room is Pure Audio, it will

automatically switch to the Direct listening mode.

4. To adjust the volume on the power amplifier in the

separate room or the ZONE 2 SPEAKER, adjust with

VOL+/– on the remote controller. To control on the main

unit, press ZONE 2 or ZONE 3 and adjust with the

MASTER VOLUME control within 8 seconds.

The information for a connected device can be displayed on the

TV screen in a separate room. Press the button while the

remote controller is in the mode for controlling ZONE 2.

0 Power consumption in standby mode increases when the

multi-zone function is being used.

To turn off the function

Press Í while in the mode for controlling ZONE 2 or ZONE

3 on the remote controller.

Playing in ZONE 2 or ZONE 3 only

If you turn the unit to standby during multi-zone playback,

the Z2 or Z3 indicator is dimmed and the playback mode is

switched to playback in a separate room only. Setting

ZONE 2/ZONE 3 to on while this unit is in standby will also

switch the playback mode to the same setting.

WHOLE HOUSE MODE

If you press WHOLE HOUSE MODE while playback is

being performed in the main room, the WHOLE HOUSE

MODE is turned on, "Z2" and "Z3" on the display light at the

same time and the playback sources of all the rooms are

switched to the same source at once.

The sources that can be played in ZONE 2 can be played in all rooms.

0 This function cannot be used if headphones are

connected or audio is output from the speakers of the TV.

Settings

Settings are required in Initial Setup, "4. Multi Zone Setup"

(



P21) to use the multi-zone feature. When checking the

setting content, refer to the following, press on the remote

controller, and check in the Setup menu that is displayed.

– When you have connected a TV in the separate room

with an HDMI cable, have you selected "Use" in "1. Input

/Output Assign" – "TV Out/OSD" – "Zone2 HDMII"?

– When you are playing the audio from an AV component in the

separate

room

connected with an HDMI cable, have you selected

"Use" in "1. Input /Output Assign" – "TV Out/OSD" – "Zone2 HDMI"?

– When you have connected speakers in a separate room

with speaker cable, have you selected "Zone 2" (or "Zone 2

A + B") in "2. Speaker" – "Configuration" – "Zone Speaker"?

– When you have connected a power amplifier in a separate

room with an analog audio cable and you want to control the

volume with this unit, have you selected "Variable" in "

Multi Zone

" – "Zone 2" or "Zone 3" – "Output Level"?

Others

To adjust the sound quality

It is possible to enhance or moderate the bass and treble of

front speakers. Press TONE on the main unit several times

to select the desired setting from "Bass" and "Treble", and

turn the TONE dial to adjust.

0 You can also adjust the sound quality of a power

amplifier connected in a separate room. After pressing

either ZONE 2 or ZONE 3 on the main unit, within

8 seconds press TONE and turn the TONE dial to adjust.

This cannot be set if the listening mode is Pure Audio or Direct.

Quick Menu

By pressing Q on the remote controller during play, you can

adjust frequently used settings, such as the sound quality,

using on-screen menus. Select the item with the cursors of

the remote controller and press ENTER to confirm your

selection. To return to the previous screen, press .

"Tone": It is possible to enhance or moderate the bass and

treble of front speakers.

"Other": Enables you to make a variety of settings.

0 "Speaker Layout": You can switch the output on the

surround back speakers and height speakers.

0 "A/V Sync": If the video is behind the audio, you can

delay the audio to offset the gap.

0 "Music Optimizer": Improve the quality of compressed

audio.

0 "HDMI Out": Allows you to select the HDMI OUT jack to

output video signals from "MAIN", "SUB", and

"MAIN+SUB".

When the unit is operating erratically

Try restarting the unit

Restarting the unit may help it operate more smoothly. To

restart the unit, turn it to standby, and then press Í ON/

STANDBY on the main unit for at least 5 seconds. (The

unit’s settings will be maintained.) If there is no

improvement even after the unit is restarted, try

disconnecting and reconnecting the power cords of the unit

and connected equipment.

Resetting the unit (this resets the unit settings to the

default)

If restarting the unit doesn't fix the problem, resetting the

unit to the status at the time of shipment may solve the

problem. If you reset the unit status, your preferences will

be reset to the defaults. Note them down before the

operation below.

1. While pressing the CBL input selector button on the main

unit, press Í ON/STANDBY.

2. "Clear" appears on the display and the unit returns to

standby. Do not unplug the power cord until "Clear"

disappears from the display.

To reset the remote controller, while holding down MODE,

press until the remote indicator flash twice (about

3 seconds).

Quick Menu

Tone

Level

AccuEQ

Other

Bass

Treble

BD/DVD

Onkyo TX-RZ810 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-RZ810

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info