Bedienungsanleitung Onkyo TX-SR307 (Seite 68 von 72) (Englisch)

645326

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Troubleshooting

If you have any trouble using the AV receiver, look for a

solution in this section. If you can’t resolve the issue

yourself, contact your Onkyo dealer.

Can’t turn on the AV receiver

• Make sure that the power cord is plugged into the wall

outlet properly.

• Unplug the power cord from the wall outlet, wait 5

seconds or more, then plug it back in again.

The AV receiver turns off as soon as it’s turned

• The amp protection circuit has been activated.

Remove the power cord from the wall outlet

immediately. Disconnect all speaker cables and input

sources, and leave the AV receiver with its power cord

disconnected for 1 hour. After that, reconnect the

power cord and set the volume to maximum. If the AV

receiver stays on, set the volume to minimum,

disconnect the power cord, and reconnect your

speakers and input sources. If the AV receiver turns off

when you set the volume to maximum, disconnect the

power cord, and contact your Onkyo dealer.

There’s no sound or it’s very quiet

• Press the SPEAKERS [A] or [B] button to turn on the

indicator for the speakers that you want to output

sound.

• HDMI audio is passed through the AV receiver and

can only be heard from your TV.

• To listen to an audio source that’s connected to an

OPTICAL or COAXIAL input, make sure that input is

assigned to an input selector (page 36).

• Make sure that all audio connecting plugs are pushed

in all the way (page 18).

• Make sure that the polarity of the speaker cables is

correct, and that the bare wire is in contact with the

metal part of each speaker terminal (page 14).

• Make sure that the speaker cables are not shorting.

• Check the volume (page 38). The AV receiver is

designed for home theater enjoyment and has a wide

volume range for precise adjustment.

• If the MUTING indicator is flashing on the display,

press the remote controller’s [MUTING] button to

unmute the AV receiver (page 39).

• While a pair of headphones is connected to the

PHONES jack, no sound is output by the main room

speakers (page 40).

• Check the digital audio output settings on the source

component. On some game consoles, such as those

that can play DVDs, the default setting is off.

• With some DVD-Video discs, you need to select an

audio format from a menu or with the [AUDIO] button

on your DVD player’s remote controller.

• If your turntable doesn’t have a phono preamp built-

in, you must connect one between it and the AV

receiver.

• If your turntable uses an MC cartridge, you must

connect an MC head amp, or an MC transformer and

a phono preamp.

• Check the speaker settings (pages 54–56).

• If the digital signal format is set to PCM or DTS, set it

to “Auto” (page 41).

Only the front speakers produce sound

• When the Stereo or Mono listening mode is selected,

only the front speakers and subwoofer produce sound.

• Check the “3. Sp Config” (page 54).

Only the center speaker produces sound

• If you use the Dolby Pro Logic II Movie or Dolby Pro

Logic II Music listening mode with a mono source,

such as an AM radio station or mono TV program, the

sound will be concentrated in the center speaker.

• Check the “3. Sp Config” (page 54).

The center speaker produces no sound

• When the Stereo or Mono listening mode is selected,

the center speaker produces no sound (page 53).

• Check the “3. Sp Config” (page 54).

The surround speakers produce no sound

• When the Stereo or Mono listening mode is selected,

the surround speakers produce no sound.

• Depending on the source and the current listening

mode, not much sound may be produced by the

surround speakers. Try another listening mode

(page 49).

• Check the “3. Sp Config” (page 54).

Power

Audio

If you can’t resolve the issue yourself, try resetting

the AV receiver before contacting your Onkyo

dealer.

To reset the AV receiver to its factory defaults,

turn it on and, while holding down the [VCR/DVR]

button, press the [ON/STANDBY] button. “Clear”

will appear on the display and the AV receiver will

enter Standby mode.

Note that resetting the AV receiver will delete your

radio presets and custom settings.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR307 Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR307

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info