Bedienungsanleitung Onkyo TX-SR393 (Seite 81 von 95) (Englisch)

686348

Zoom out

Zoom in

Vorherige Seite

1/95

Nächste Seite

Front Panel≫ Rear Panel≫ Remote≫

Contents

≫

Connections

≫

Playback

≫

Setup

≫

 1. Speaker Setup

1. Select the connected speaker conguration, and press ENTER.

Note that the image on the screen changes each time you select the number

of channels in "Speaker Channels".

Speaker Setup

Select how many speakers you have.

ENTER

Speaker Channels

Speaker Impedance

5.1 ch

Yes

6 ohms or above

Subwoofer

- - -Height Speaker

2. The speaker combination selected in step 1 is displayed. "Yes" is displayed for

the selected speakers. If the setting is correct, press ENTER.

3. Select "Next" and press ENTER. Then a test tone is output from each speaker

to conrm the connection. Selecting each speaker with the cursors / will

output the test tone. Press ENTER after conrmation.

4. If there is no problem with the speaker connection, select "Next" and press

ENTER. To return to "Speaker Setup", select "Back to Speaker Setup" and

press ENTER.

 2. AccuEQ Room Calibration

Place the supplied speaker setup microphone at the listening position. The unit

automatically measures the test tones output from each speaker, and sets the

optimum volume level for each speaker, the crossover frequencies, and the

distance from the listening position. This also automatically adjusts the equalizers

for the speakers, and enables correction of sound distortion caused by the

acoustic environment of the room.

• It takes between 3 and 12 minutes for calibration to be completed. Each

speaker outputs the test tone at high volume during measurement, so be

careful of your surroundings. Also, keep the room as quiet as possible during

measurement.

• If you connect a subwoofer, check the power and volume of the subwoofer.

Set the subwoofer volume to more than half.

• If the power of this unit suddenly turns o, the wires in the speaker cables

have touched the rear panel or other wires, and the protection circuit is

working. Twist the wires again securely, and make sure they do not stick out of

the speaker terminals when connecting.

1. Place the supplied speaker setup microphone at the listening position, and

connect it to the SETUP MIC jack on the main unit.

SETUP MI

When placing the speaker setup microphone on a tripod, refer to the

illustration.

2. Conrm a test tone is output from the subwoofer and press ENTER.

3. Press ENTER. Then, test tones are output from each speaker, and the

connected speakers and the noise in the surrounding environment are

automatically measured.

4. The measurement results in step 3 are displayed. Select "Next", and press

ENTER. The test tones are output again. Then, the unit automatically sets the

optimum volume level, crossover frequency, etc.

5. When the measurement is completed, the measurement results are displayed.

You can check each setting using the cursors / . Select "Save" and press

ENTER to save the settings.

6. Disconnect the speaker setup microphone.

 3. ARC Setup

To connect with an ARC-compatible TV, select "Yes". The ARC setting on this unit

turns on, and you can listen to the TV's audio through this unit.

• If you select "Yes", the HDMI CEC function is enabled and power consumption

increases during standby.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR393 Seite 81

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR393

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info