Bedienungsanleitung Onkyo TX-SR502 (Seite 57 von 60) (Englisch)

645312

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Troubleshooting

—Continued

Symptom Possible cause Remedy

Audio

The surround back speak-

ers produce no sound?

The level of the surround back speaker is set

at minimum.

Check the volume of the surround back

speaker (page 49).

The Surround Back setting is set to None in

the Speaker Conﬁguration.

Check the Surround Back setting in the

Speaker Conﬁguration (page 32).

The selected listening mode doesn’t use the

surround back speakers.

Select another listening mode. See page 42

for information on listening modes.

Surround speaker output depends on the

source material, and some material may not

use the surround speakers much.

If you’re playing a Dolby Digital EX or

DTS-ES source, make sure that the Dolby

Digital/DTS setting is set to On (page 44).

A low-frequency noise or

hum can be heard?

The audio connecting cables at the rear of

the TX-SR502/TX-SR502E are too close to

the power cord.

Untangle the audio cables and position them

as far away as possible from the power cord.

The sound is too bright or

harsh and the high range is

not clear?

The treble is set too high. Adjust the treble (page 38).

The subwoofer is not work-

ing or is very quiet?

The Subwoofer setting is set to No in the

Speaker Conﬁguration.

Check the Subwoofer setting in the Speaker

Conﬁguration (page 32).

The volume of the subwoofer is set at mini-

mum.

Check the volume of the subwoofer

(page 49, 35).

Speaker set A is turned off. The subwoofer

output does not work while only speaker set

B is on.

Turn on speaker set A.

Video

There’s no picture on the

TV?

The Pure Audio listening mode is selected.

When this mode is selected, the display and

the internal video circuits are all turned off

and no video signals are output.

The TV’s input selector is set incorrectly.

Select the correct input on the TV (i.e., the

input to which the TX-SR502/TX-SR502E is

connected).

The video input and output are different for-

mats.

The TX-SR502/TX-SR502E doesn’t convert

between video formats. It works as a video

signal switcher. Composite video input sig-

nals are output only by composite video out-

puts. S-Video input signals are output only

by S-Video outputs. And component video

input signals are output only by component

video outputs.

Remote controller

The buttons on the

TX-SR502/TX-SR502E work

OK but those on the remote

controller don’t?

The wrong remote controller mode is

selected.

Select the correct mode (page 10).

The batteries are installed incorrectly.

Check the batteries and correct as necessary

(page 9).

You’re not pointing the remote controller at

the TX-SR502/TX-SR502E’s remote sensor.

Point the remote controller at the TX-SR502/

TX-SR502E’s remote sensor (page 9).

Can’t use the remote con-

troller with other AV com-

ponents?

You’ve connected a MiniDisc recorder or

CD recorder to the TX-SR502/TX-SR502E

but haven’t changed the TAPE/MD/CDR

display.

Press and hold the [TAPE] input selector

button until MD or CDR, as appropriate,

appears on the display.

The wrong remote control code has been

entered.

If more than one code is listed, try each one

(page 50).

With some AV components, certain buttons

may not work as expected and some may not

work at all.

You’re pointing the remote controller at the

wrong AV component.

To control a component connected via ,

point the remote controller at the TX-SR502/

TX-SR502E. To control a component that’s

not connected via , point the remote con-

troller at that component (page 50)

You’ve made an connection but not an

analog audio connection (RCA).

To use , you must make an connection

and an analog audio connection (RCA)

between the component and TX-SR502/

TX-SR502E, even if they are connected dig-

itally (page 30).

TX-SR502_En.book Page 57 Tuesday, February 17, 2004 12:14 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR502 Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR502

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info