Bedienungsanleitung Onkyo TX-SR504E (Seite 64 von 80) (Englisch)

645342

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Troubleshooting

—Continued

The remote controller doesn’t work

• Make sure that the batteries are installed with the cor-

rect polarity (page 11).

• Make sure that the remote controller is not too far

away from the AV receiver, and that there’s no

obstruction between the remote controller and the AV

receiver’s remote control sensor (page 11).

• Make sure you’ve selected the correct remote control-

ler mode (page 12).

• Make sure you’ve entered the correct remote control

code (page 59).

Can’t control other components

• Make sure you’ve selected the correct remote control-

ler mode (page 12).

• If you’ve connected an -capable Onkyo MD

recorder, CD recorder, or next generation HDD-com-

patible component to the TAPE IN/OUT jacks, or a

DS-A1 Remote Interactive Dock to the VIDEO 2 IN

jacks, for the remote controller to work properly, you

must set the Input Display to MD, CDR, or HDD (see

page 33).

• The entered remote control code may not be correct. If

more than one code is listed, try each one.

•With some AV components, certain buttons may not

work as expected, and some may not work at all.

•To control an Onkyo component that’s connected via

, point the remote controller at the AV receiver. Be

sure to enter the appropriate remote control code ﬁrst

(see page 60).

•To control an Onkyo component that’s not connected

via , or another manufacturer’s component, point

the remote controller at the component. Be sure to

enter the appropriate remote control code ﬁrst (see

page 59).

Can’t record

• On your recorder, make sure the correct input is

selected.

•To prevent signal loops and damage to the AV

receiver, input signals are not fed through to outputs

with the same name (e.g., TAPE IN to TAPE OUT, or

VIDEO 1 IN to VIDEO 1 OUT).

• When the Pure Audio listening mode is selected,

recording is not possible because no video signals are

output. Select another listening mode.

The sound changes when I connect my head-

phones

• When a pair of headphones is connected, the listening

mode is set to Stereo, unless it’s already set to Stereo,

Mono, Direct, or Pure Audio (not North American

model).

The display doesn’t work

• The display is turned off when the Pure Audio (not

North American model) listening mode is selected.

How do I change the language of a multiplex

source

• Use the “Multiplex” setting on the “4. Audio Adjust”

menu to select Main or Sub (page 53).

The functions don’t work

•To use , you must make an connection and an

analog audio connection (RCA) between the compo-

nent and AV receiver, even if they are connected digi-

tally (page 31).

Remote Controller

Recording

Others

TX-SR504_En.book Page 64 Thursday, February 2, 2006 3:46 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR504E Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR504E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info