Bedienungsanleitung Onkyo TX-SR602 (Seite 47 von 96) (Englisch)

645309

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

First Time Setup

—Continued

Crossover

Notes:

• If the crossover frequency is set to a low value, and the

program material doesn’t contain any sounds below

that frequency, the subwoofer will not output much

sound.

Use the Up and Down [ ]/[ ]

buttons to select “c. Center,” and

then use the Left and Right [ ]/

[] buttons to select:

Small:

Select if the center speaker is

small.

Large:

Select if the center speaker is

large.

None:

Select if no center speaker is

connected.

Note:

• If the Front setting in step 5 is set to

Small, the Large option cannot be

selected.

Use the Up and Down [ ]/[ ]

buttons to select “d. Surround,”

and then use the Left and Right

[ ]/[ ] buttons to select:

Small:

Select if the surround left and

right speakers are small.

Large:

Select if the surround left and

right speakers are large.

None:

Select if no surround left and

right speakers are connected.

Note:

• If the Front setting in step 5 is set to

Small, the Large option cannot be

selected.

Use the Up and Down [ ]/[ ]

buttons to select “e. Surround

Back,” and then use the Left and

Right [ ]/[ ] buttons to select:

Small:

Select if the surround back

left and right speakers are

small.

Large:

Select if the surround back

speakers are large.

None:

Select if no surround back

speakers are connected.

Notes:

• If the Surround setting in step 7 is set

to None, this setting cannot be

selected.

• If the Surround setting in step 7 is set

to Small, this setting cannot be set to

Large.

ENTER

Use the Up and Down [ ]/[ ]

buttons to select “f. SurrBack

ch,” and then use the Left and

Right [ ]/[ ] buttons to select:

1ch:

Select if one surround back

speaker is connected.

2ch:

Select if two (left and right)

surround back speakers are

connected.

Continue with step 10 in the right col-

umn.

Use the Up and Down [ ]/[ ]

buttons to select “g. Crossover,”

and then use the Left and Right

[ ]/[ ] buttons to select a

crossover frequency.

Choose a crossover frequency suitable

for your setup. If you’re using a sub-

woofer, choose a crossover frequency

based on the diameter of your front

speakers. If you’re not using a sub-

woofer, use the diameter of any speaker

that you speciﬁed as Small.

For the TX-SR702/702E, if you’re

using THX-certiﬁed speakers, select

80Hz (THX).

*TX-SR702/702E only.

Continue with step 11 on the next page.

ENTER

Speaker cone

diameter

Crossover

frequency

Over 12 in.

(30 cm)

40Hz*

8 to 12 in.

(20–30 cm)

60Hz

6-1/2 to 8 in.

(16–20 cm)

80Hz (THX)

5-1/4 to 6-1/2 in.

(13–16 cm)

100Hz

3-1/2 to 5-1/4 in.

(9–13 cm)

120Hz

Under 3-1/2 in.

(9 cm)

150Hz

TX-NR702,602_En.book Page 47 Monday, July 26, 2004 11:05 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR602 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR602

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info