Bedienungsanleitung Onkyo TX-SR604E (Seite 68 von 92) (Englisch)

469192

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

Advanced Setup—Continued

Low-Pass Filter for the LFE Channel

With this setting, you can specify the cutoff frequency of

the LFE channel’s low-pass ﬁlter (LPF), which can be

used to ﬁlter out unwanted hum. The LPF only applies to

sources that use the LFE channel.

Double Bass

With the Double Bass function, you can boost bass out-

put by feeding bass sounds from the front left and right

channels to the subwoofer. This function can be set only

if the Subwoofer setting in step 3 is set to Yes, and the

Front setting in step 4 is set to Full Band.

In the speaker setup screen, you can choose how bass

information is distributed to your speakers only if you

have large front left and right speakers AND a subwoofer.

Note:

This procedure can also be performed on the AV receiver

by using its [SETUP] button, arrow buttons, and

[ENTER] button.

Use the Up and Down [ ]/[ ]

buttons to select “d. Surround,”

and then use the Left and Right

[ ]/[ ] buttons to select a

crossover frequency.

If no surround left and right speakers

are connected, select None.

Note:

If the Front setting in step 4 is set to

anything other than Full Band, Full

Band cannot be selected here.

Use the Up and Down [ ]/[ ]

buttons to select “e. SurrBack,”

and then use the Left and Right

[ ]/[ ] buttons to select a

crossover frequency.

If no surround back speakers are con-

nected, select None.

Notes:

• If the Surround setting in step 6 is set

to None, this setting cannot be

selected.

• If the Surround setting in step 6 is set

to anything other than Full Band,

Full Band cannot be selected here.

Use the Up and Down [ ]/[ ]

buttons to select “f. SurrBack

Ch,” and then use the Left and

Right [ ]/[ ] buttons to select:

1ch: Select if one surround back

speaker is connected.

2ch: Select if two (left and right)

surround back speakers are

connected.

Note:

If the Surround Back Setting in step 7 is

set to None, this setting cannot be

selected.

Continue with step 9 in the right col-

umn.

Use the Up and Down [ ]/[ ]

buttons to select “g. LPFofLFE,”

and then use the Left and Right

[ ]/[ ] buttons to select a low-

pass ﬁlter frequency.

The following low-pass ﬁlter frequen-

cies can be selected: 80 Hz, 100 Hz,

120 Hz (default), 150 Hz, or 200 Hz.

Continue with step 10 below.

Use the Up and Down [ ]/[ ]

buttons to select “h. Double

Bass,” and then use the Left and

Right [ ]/[ ] buttons to select:

On: Double Bass function on

(default). Front left and right

bass also goes to the sub-

woofer simultaneously.

Off: Double Bass function off.

Press the [SETUP] button.

The setup menu closes.

This setting is not set automatically by the Automatic

Speaker Setup function (see page 38).

This setting is not set automatically by the Automatic

Speaker Setup function (see page 38).

SETUP

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR604E Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR604E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info