Bedienungsanleitung Onkyo TX-SR702 (Seite 78 von 96) (Englisch)

645308

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Zone 2

—Continued

Here you can turn on Zone 2, select an input source, and

adjust the volume.

Note:

To control Zone 2 with the remote controller, you must

press the [ZONE 2] button ﬁrst.

Notes:

• If the Sleep function has been set, the Zone 2 compo-

nent will turn off along with the AV receiver when the

speciﬁed sleep time expires. To use the Sleep function

with Zone 2 only, set the Sleep function and then set

the AV receiver to Standby.

• Only analog input sources are output by the ZONE 2

LINE OUT and ZONE 2 SPEAKERS terminals. Dig-

ital input sources are not output. If no sound is heard

when an input source is selected, check if it’s con-

nected to an analog input.

• Since the Zone 2 function and the REC OUT outputs

use the same circuitry, if the [REC OUT] function is

used, Zone 2 will be turned off.

• While Zone 2 is being used, listening modes that need

surround back speakers (i.e., Dolby Digital EX, DTS-

ES, and THX Surround EX) are unavailable.

• While Zone 2 is on, functions will not work.

•You can’t select different radio stations for Zone 2 and

the main room. For example, if you an FM station for

the main room, that station will also be used in Zone 2.

Using Zone 2

Point the remote controller at the

AV receiver and press the

[ZONE 2] button followed by the

[ON] button.

This turns on Zone 2 and the AV

receiver’s 12V TRIGGER OUT.

To select the Zone 2 input source

with the remote controller, press

the [ZONE 2] button followed by

an input selector button.

If you select AM or FM, you can use

the remote controller’s [TUNER] but-

ton to select the band.

To perform steps 1 and 2 on the

AV receiver, press the [ZONE 2]

button, and then use the Control-

ler [ ]/[ ] buttons within ﬁve

seconds.

The name of the selected Zone 2 source

appears on the display.

1–4

ZONE

To set Zone 2 to the same source as the

main room, press the [ZONE 2] button,

and then use the Controller [ ]/[ ]

buttons to select “Zone 2 Sel: Source.”

To adjust the Zone 2 volume with

the remote controller, press the

[ZONE 2] button, and then use

the [LEVEL–] and [LEVEL+] but-

tons.

To do this on the AV receiver,

press the ZONE 2 [LEVEL] but-

ton, and then use the Controller

[ ]/[ ] buttons.

If the Zone 2 receiver/integrated amp is

connected to the AV receiver’s ZONE 2

LINE OUT L/R jacks, use the volume

control on the receiver/integrated amp.

To turn off Zone 2 with the

remote controller, press the

[ZONE 2] button followed by the

[STANDBY] button.

To do this from the AV receiver,

press the [ZONE 2] button, and

then use the Controller [ ]/[ ]

buttons to select OFF.

ZONE

LEVEL

ZONE

STANDBY

TX-NR702,602_En.book Page 78 Monday, July 26, 2004 11:05 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR702 Seite 78

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR702

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info