Bedienungsanleitung Onkyo TX-SR703 (Seite 93 von 96) (Englisch)

645333

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Troubleshooting

—Continued

Reception is noisy, stereo FM reception suffers

from hiss, or the FM STEREO indicator doesn’t

appear

• Relocate your antenna.

•Move the AV receiver away from your TV or com-

puter.

• Listen to the station in mono (page 49).

• When listening to an AM station, operating the remote

controller may cause noise.

•Passing cars and airplanes can cause interference.

• Concrete walls weaken radio signals.

• If nothing improves the reception, install an outdoor

antenna.

Can’t select XM radio channels (North Ameri-

can model only)

• Channels cannot be selected while the indica-

tor is ﬂashing, as tuning is in progress.

The remote controller doesn’t work

• Make sure that the batteries are installed with the cor-

rect polarity (page 13).

• Make sure that the remote controller is not too far

away from the AV receiver, and that there’s no

obstruction between the remote controller and the AV

receiver’s remote control sensor (page 13).

• Make sure you’ve selected the correct remote control-

ler mode (page 14).

• Make sure you’ve entered the correct remote control

code (page 86).

Can’t control other components

• Make sure you’ve selected the correct remote control-

ler mode (page 14).

• If you’ve connected an -capable Onkyo MD

recorder, CD recorder, or next generation HDD-com-

patible component to the TAPE IN/OUT jacks, or a

DS-A1 Remote Interactive Dock to the VIDEO 3 IN

jacks, for the remote controller to work properly, you

must set the input display to MD, CDR, or HDD (see

page 46).

• The entered remote control code may not be correct. If

more than one code is listed, try each one.

• If none of the codes work, use the Learning function

to learn the commands of the other component’s

remote controller (page 89).

•With some AV components, certain buttons may not

work as expected, and some may not work at all.

•To control an Onkyo component that’s connected via

, point the remote controller at the AV receiver. Be

sure to enter the appropriate remote control code ﬁrst

(page 87).

•To control an Onkyo component that’s not connected

via , or another manufacturer’s component, point

the remote controller at the component. Be sure to

enter the appropriate remote control code ﬁrst

(page 86).

Can’t learn commands from another remote

controller

• When learning commands, make sure that the trans-

mitting ends of both remote controllers are pointing at

each other.

• Are you trying to learn from a remote controller that

cannot be used for learning? Some commands cannot

be learned, especially those that contain several

instructions.

Can’t record

• On your recorder, make sure the correct input is

selected.

•To prevent signal loops and damage to the AV

receiver, input signals are not fed through to outputs

with the same name (e.g., TAPE IN to TAPE OUT,

VIDEO 1 IN to VIDEO 1 OUT, or VIDEO 2 IN to

VIDEO 2 OUT).

• When the Pure Audio listening mode is selected, video

recording is not possible because no video signals are

output. Select another listening mode.

The sound changes when I connect my head-

phones

• When a pair of headphones is connected, the listening

mode is set to Stereo, unless it’s already set to Stereo,

Mono, Direct, or Pure Audio, in which case it stays the

same.

How do I change the language of a multiplex

source

• Use the “Multiplex” setting on the “Audio Adjust”

menus to select “Main” or “Sub” (page 68).

The functions don’t work

•To use , you must make an connection and an

analog audio connection (RCA) between the compo-

nent and AV receiver, even if they are connected digi-

tally (page 35).

• While Zone 2 is on, the functions do not work.

The AV receiver’s display doesn’t work

• The display is turned off when the Pure Audio listen-

ing mode is selected.

Tuner

Remote Controller

Recording

Others

TX-SR803_En.book Page 93 Friday, August 26, 2005 9:26 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR703 Seite 93

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info