Bedienungsanleitung Onkyo TX-SR706 (Seite 115 von 120) (Englisch)

62817

115

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

115

Troubleshooting—Continued

The center speaker produces no sound

• When the Stereo listening mode is selected, the center

speaker produces no sound.

• In the Mono listening mode, only the front speakers

output sound if the “Output Speaker” setting is set to

“Left/Right” (page 81).

• Make sure the speakers are configured correctly

(page 73).

The surround back speakers produce no sound

• The surround back speakers are not used with all lis-

tening modes. Select another listening mode

(page 69).

• Not much sound may be produced by the surround

back speakers with some sources.

• Make sure the speakers are configured correctly

(page 73).

• While Powered Zone 2 is being used, playback in the

main room is reduced to 5.1-channels and the sur-

round back speakers produce no sound (page 97).

The subwoofer produces no sound

• When you play source material that contains no infor-

mation in the LFE channel, the subwoofer produces

no sound.

• Make sure the speakers are configured correctly

(page 73).

There’s no sound with a certain signal format

• Check the digital audio output setting on the con-

nected device. On some game consoles, such as those

that support DVD, the default setting is off.

• With some DVD-Video discs, you need to select an

audio output format from a menu.

• Depending on the input signal, some listening modes

cannot be selected (pages 63-68).

Can’t select the Pure Audio listening mode

• The Pure Audio listening mode cannot be selected

while Zone 2 is on.

Can’t get 6.1/7.1 playback

• If no surround back speakers are connected, or the

Zone 2 speakers are being used, 6.1/7.1 playback is

not possible.

• You can not always select all of the listening modes,

depending on the number of the speakers connected

(pages 63-68).

The speaker volume cannot be set as required

(The volume cannot be set to +18.0 dB)

• Check to see if a maximum volume has been set

(page 89).

• After the Automatic Speaker Setup function has been

run, or the volume level of each individual speaker has

been adjusted (page 77), the maximum volume may

be reduced.

• When the “Equalizer Settings” (page 78) is set to

“Audyssey”, the maximum possible volume is

reduced by 6 dB.

Noise can be heard

• Using cable ties to bundle audio cables with power

cords, speaker cables, and so on may degrade the

audio performance, so don’t do it.

• An audio cable may be picking up interference. Try

repositioning your cables.

The Late Night function doesn’t work

• Make sure the source material is Dolby Digital, Dolby

Digital Plus, and Dolby TrueHD (page 83).

The DVD analog multichannel input doesn’t

work

• Check the DVD analog multichannel input connec-

tions (page 27).

• To select the DVD analog multichannel input, press

the [MULTI CH] input selector button.

• Make sure that the “Speakers Type” is not set to “Bi-

Amp”. The multichannel DVD input cannot be used if

“Speakers Type” is set to “Bi-Amp” (page 45).

• Check the audio output settings on your DVD player.

About DTS signals

• When DTS program material ends and the DTS bit-

stream stops, the AV receiver/AV amplifier remains in

DTS listening mode and the DTS indicator remains

on. This is to prevent noise when you use the pause,

fast forward, or fast reverse function on your player. If

you switch your player from DTS to PCM, because

the AV receiver/AV amplifier does not switch formats

immediately, you may not hear any sound, in which

case you should stop your player for about three sec-

onds, and then resume playback.

• With some CD and LD players, you won’t be able to

playback DTS material properly even though your

player is connected to a digital input on the AV

receiver/AV amplifier. This is usually because the

DTS bitstream has been processed (e.g., output level,

sampling rate, or frequency response changed) and the

AV receiver/AV amplifier doesn’t recognize it as a

genuine DTS signal. In such cases, you may hear

noise.

• When playing DTS program material, using the pause,

fast forward, or fast reverse function on your player

may produce a short audible noise. This is not a mal-

function.

The beginning of audio received by an HDMI IN

can’t be heard

• Since it takes longer to identify the format of an

HDMI signal than it does for other digital audio sig-

nals, audio output may not start immediately.

There’s no picture

• Make sure that all video connecting plugs are pushed

in all the way (page 22).

• Make sure that each video component is properly con-

nected. (pages 25-38)

Video

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR706 Seite 115

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR706

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info