Bedienungsanleitung Onkyo TX-SR804 (Seite 71 von 96) (Englisch)

645329

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Advanced Setup

—Continued

Low-Pass Filter for the LFE Channel

With this setting, you can specify the cutoff frequency of

the LFE channel’s low-pass ﬁlter (LPF), which can be

used to ﬁlter out unwanted hum. The LPF only applies to

sources that use the LFE channel.

*If you are using THX-certiﬁed speakers, select 80 Hz (THX).

Subwoofer Mode

With this setting, you can boost bass output by feeding

front left and right channel bass sounds to the subwoofer.

This setting can only be made if the Subwoofer setting in

step 4 is set to Yes, and the Front setting in step 5 is set

to Full Band.

*If you are using THX-certiﬁed speakers, select LFE only

(THX).

Note:

• These procedures can also be performed on the AV

receiver by using its [SETUP] button, arrow buttons,

and [ENTER] button.

Use the Up and Down [ ]/[ ]

buttons to select “d. Surround,”

and then use the Left and Right

[ ]/[ ] buttons to select a

crossover frequency.

If no surround left and right speakers

are connected, select None.

Note:

• If the Front setting in step 5 is set to

anything other than Full Band, Full

Band cannot be selected here.

Use the Up and Down [ ]/[ ]

buttons to select “e. SurrBack,”

and then use the Left and Right

[ ]/[ ] buttons to select a

crossover frequency.

If no surround back speakers are con-

nected, select None.

Notes:

• If the Surround setting in step 7 is set

to None, this setting cannot be

selected.

• If the Surround setting in step 7 is set

to anything other than Full Band,

Full Band cannot be selected here.

Use the Up and Down [ ]/[ ]

buttons to select “f. SurrBack

Ch,” and then use the Left and

Right [ ]/[ ] buttons to select:

1ch:

Select if one surround back

speaker is connected.

2ch:

Select if two (left and right)

surround back speakers are

connected.

Continue with step 10 in the next col-

umn.

ENTER

Use the Up and Down [ ]/[ ]

buttons to select “g.LPF of LFE,”

and then use the Left and Right

[ ]/[ ] buttons to select a low-

pass ﬁlter frequency.

The following low-pass ﬁlter frequen-

cies can be selected: 80 Hz (THX)

(default), 90 Hz, 100 Hz, or 120 Hz.

Continue with step 11 below.

Use the Up and Down [ ]/[ ]

buttons to select “h. Subwoofer

Mode,” and then use the Left and

Right [ ]/[ ] buttons to select:

LFE only (THX):

The subwoofer only

outputs the LFE channel.

Double Bass:

In addition to LFE chan-

nel sounds, the subwoofer outputs front

left and right channel bass sounds.

Press the [SETUP] button.

Setup closes.

This setting is not set automatically by the Automatic

Speaker Setup function (see page 40).

ENTER

This setting is not set automatically by the Automatic

Speaker Setup function (see page 40).

ENTER

TX-SR804/804E_En.book Page 71 Monday, September 4, 2006 9:34 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR804 Seite 71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR804

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info