Bedienungsanleitung Onkyo TX-SR804E (Seite 70 von 96) (Englisch)

645328

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Advanced Setup

This section explains how to check the speaker settings

and how to set them manually, which is useful if you

change a speaker after performing the automatic speaker

setup.

Some speaker settings are set automatically by the Auto-

matic Speaker Setup function (see page 40).

Speaker Conﬁguration

With these settings, you can specify which speakers are

connected and a crossover frequency for each speaker.

The following crossover frequencies can be speciﬁed:

Full Band, 40 Hz, 60 Hz, 70 Hz, 80 Hz (THX), 90 Hz,

100 Hz, 120 Hz, 150 Hz, 200 Hz.

Specify Full Band for speakers that can output low-fre-

quency bass sounds adequately, for example, speakers

with a good sized woofer. For smaller speakers, specify

a crossover frequency. Sounds below the crossover fre-

quency will be output by the subwoofer instead of the

speaker. Refer to your speakers’ manuals to determine

the optimum crossover frequencies.

If you’re using THX-certiﬁed speakers, specify

80 Hz (THX) for all speakers.

Speaker Setup

Press the [RECEIVER] REMOTE

MODE button, followed by the

[SETUP] button.

The main menu appears onscreen.

THX

--/---

11 12

REMOTE MODE

HDD

RECEIVER

TAPE/AMP

DVD CD

ZONE2

SAT

VCR

CABLE

MDCDR

STEREO

SURR

DIRECT

SUBTITLEAUDIO

ALLST

PLAY MODE

REPEAT

RANDOMREC PLAYLIST

V CH

V VOL

ENTER

VOL

DISPLAY

DIMMER

SLEEP

MUTING

LISTENING MODE

INPUT SELECTOR

MACRO

10 0

CLEAR

456

789

MULTI CH

DVD

TUNER

PHONO

DISC

ALBUM

TAPE

PURE A

SETUP

RECEIVER

ENTER

These settings are set automatically by the Automatic

Speaker Setup function (see page 40).

RECEIVER

Use the Up and Down [ ]/[ ]

buttons to select “3. Speaker

Setup,” and then press [ENTER].

The Speaker Setup menu appears.

Use the Up and Down [ ]/[ ]

buttons to select “Speaker Con-

ﬁguration,” and then press

[ENTER].

The Speaker Conﬁg menu appears.

Use the Up and Down [ ]/[ ]

buttons to select “a. Subwoofer,”

and then use the Left and Right

[ ]/[ ] buttons to select:

Yes:

Select if a subwoofer is con-

nected.

No:

Select if no subwoofer is con-

nected.

Use the Up and Down [ ]/[ ]

buttons to select “b. Front,” and

then use the Left and Right

[ ]/[ ] buttons to select a

crossover frequency.

Note:

• If the Subwoofer setting in step 4 is

set to No, this is ﬁxed at Full Band.

Use the Up and Down [ ]/[ ]

buttons to select “c. Center,” and

then use the Left and Right

[ ]/[ ] buttons to select a

crossover frequency.

If no center speaker is connected, select

None.

Note:

• If the Front setting in step 5 is set to

anything other than Full Band, Full

Band cannot be selected here.

ENTER

3-2.Speaker Config

------------------------

a.Subwoofer :Yes

b.Front :80Hz(THX)

c.Center :80Hz(THX)

d.Surround :80Hz(THX)

e.SurrBack :80Hz(THX)

f.SurrBack Ch :2ch

g.LPF of LFE

:80Hz(THX)

h.Subwoofer Mode

:-------------

ENTER

TX-SR804/804E_En.book Page 70 Monday, September 4, 2006 9:34 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR804E Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR804E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info