Bedienungsanleitung Onkyo TX-SR804E (Seite 92 von 96) (Englisch)

645328

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Troubleshooting

—Continued

The subwoofer produces no sound

• When you play source material that contains no infor-

mation in the LFE channel, the subwoofer produces

no sound.

• Make sure the speakers are conﬁgured correctly

(pages 70, 71).

The Zone 2 speakers produce no sound

• The Zone 2 speakers only output sources that are con-

nected to an analog input. Check to see if the source is

connected to an analog input.

There’s no sound with a certain signal format

• Check the digital audio output setting on the con-

nected device. On some games consoles, such as those

that can play DVDs, the default setting is off.

•With some DVD-Video discs, you need to select an

audio output format from a menu.

Can’t get 6.1- or 7.1-channel playback

• When the ZONE 2 SPEAKERS terminals are used,

playback in the main room is reduced to 5.1-channels.

The volume cannot be set to +18 dB (99)

• After the Automatic Speaker Setup function has been

used, or the volume level of each speaker has been

adjusted (pages 58, 73), the maximum possible vol-

ume setting be reduced.

Noise can be heard

• Using cable ties to bundle audio cables with power

cords, speaker cables, and so on may degrade the

audio performance, so don’t do it.

• An audio cable may be picking up interference. Try

repositioning your cables.

The Late Night function doesn’t work

• Make sure the source material is Dolby Digital

(page 68).

The multichannel DVD input doesn’t work

• Check the multichannel DVD input connections

(page 28).

•To select the multichannel DVD input, press the

[MULTI CH] input selector button.

• Check the audio output settings on your DVD player.

About DTS signals

• When playing DTS program material, using the pause,

fast forward, or fast reverse function on your player

may produce a short audible noise. This is not a mal-

function.

• When DTS program material ends and the DTS bit-

stream stops, the AV receiver remains in DTS listen-

ing mode and the DTS indicator remains on. This is to

prevent noise when you use the pause, fast forward, or

fast reverse function on your player. If you switch your

player from DTS to PCM, because the AV receiver

does not switch formats immediately, you may not

hear any sound, in which case you should stop your

player for about 3 seconds, and then resume playback.

•With some CD players, you won’t be able to playback

DTS material properly even though your player is con-

nected to a digital input on the AV receiver. This is

usually because the DTS bitstream has been processed

(e.g., output level, sampling rate, or frequency

response changed) and the AV receiver doesn’t recog-

nize it as a genuine DTS signal. In such cases, you

may hear noise.

The beginning of audio received by an HDMI IN

can’t be heard

• Since it takes longer to identify the format of an

HDMI signal than it does for other digital audio sig-

nals, audio output may not start immediately.

There’s no picture

• Make sure that all video connecting plugs are pushed

in all the way (page 24).

• Make sure that each video component is properly con-

nected.

• If a video component is connected to a component

video input, your TV must be connected to the COM-

PONENT VIDEO OUT or HDMI OUT (page 25).

• If a video component is connected to an HDMI input,

your TV must be connected to the HDMI OUT.

• While the Pure Audio listening mode is selected, the

video circuitry is turned off and only the HDMI OUT

outputs video signals.

• On your TV, make sure that the video input to which

the AV receiver is connected is selected.

•To watch a composite video or S-Video source on a

TV that’s connected to the COMPONENT VIDEO

OUT, select “- - -” in the “Component Video Setup” on

page 44.

•To watch a composite video, S-Video, or component

video source on a TV that’s connected to the HDMI

OUT, select “- - -” in the “HDMI Video Setup” on

page 43.

There’s no picture from a source connected to

an HDMI IN

• If the message “Resolution Error” appears on the AV

receiver’s display, this indicates that the TV or display

does not support the current video resolution and you

need to select another resolution on your DVD player.

The onscreen menus don’t appear

• On your TV, make sure that the video input to which

the AV receiver is connected is selected.

The picture is distorted

• On non-North American models, specify the TV sys-

tem used in your area in the “TV Format Setup” on

page 47.

The immediate display does not appear

• The immediate display (operation details) may not

appear on a TV that’s connected to the HDMI OUT or

COMPONENT VIDEO OUT.

Video

TX-SR804/804E_En.book Page 92 Monday, September 4, 2006 9:34 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR804E Seite 92

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR804E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info