Bedienungsanleitung Onkyo TX-SR806 (Seite 34 von 124) (Englisch)

63833

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Connecting the AV Receiver/AV Amplifier—Continued

Making HDMI Connections

■ Video Signals

Digital video signals received by the HDMI IN jacks are normally output by the HDMI OUT for display on your TV.

Composite video, S-Video, and component video sources can be upconverted for the HDMI output. See “Video Con-

nection Formats” on page 23 for more information.

■ Audio Signals

Digital audio signals received by the HDMI IN jacks are output by the speakers and headphones connected to the AV

receiver/AV amplifier. Normally, they are not output by the HDMI OUT, unless the “Audio TV Out” setting is set to

“On” (see page 95).

To listen to audio received by the HDMI IN jacks through your TV’s speakers, set the “Audio TV Out”

setting to “On” (see page 95), and set your DVD player’s HDMI audio output setting to PCM.

Notes:

• The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can

be connected by using an HDMI-to-DVI adapter cable. (Note that DVI connections only carry video, so you’ll need

to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In

addition, video signals from a PC are not supported.

• When listening to an HDMI component through the AV receiver/AV amplifier, set the HDMI component so that its

video can be seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV

receiver/AV amplifier). If the TV power is off or the TV is set to another input source, this may result in no sound

from the AV receiver/AV amplifier or the sound may be cut off.

• When the “Audio TV Out” setting is set to “On” (see page 95), or “TV Control” is set to “Enable” (see page 96) and

you’re listening through your TV’s speakers, if you turn up the AV receiver/AV amplifier volume control, the sound

will be output by the AV receiver/AV amplifier’s speakers. To stop the AV receiver/AV amplifier’s speakers producing

sound, change the settings, change your TV’s settings, or turn down the AV receiver/AV amplifier’s volume.

• The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the

picture is poor or there’s no sound from a component connected via HDMI, check its setup. Refer to the connected

component’s instruction manual for details.

Step 1:

Use HDMI cables to connect the AV receiver/AV amplifier’s HDMI jacks to your HDMI-compatible Blu-ray

player/DVD player, TV, projector, and so on.

Step 2:

Assign each HDMI IN to an input selector in the HDMI Input Setup (see page 44).

Hint!

HDMI

HDMI HDMI

IN 1

(DVD)

HDMI

OUT

Blu-ray player/DVD player

TX-SR806_En.book Page 34 Monday, August 4, 2008 10:25 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR806 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR806

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info