Bedienungsanleitung Onkyo TX-SR806 (Seite 57 von 124) (Englisch)

63833

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Basic Operations—Continued

The multichannel DVD input is for connecting a compo-

nent with a 7.1-channel analog audio output, such as a

DVD-Audio or SACD-capable DVD player, or an

MPEG decoder. See page 27 for hookup information.

Notes:

• While the multichannel DVD input is selected, the

Speaker Configuration settings on page 75 are

ignored, and signals from the multichannel input are

fed to the speakers as they are.

• The multichannel DVD input cannot be used if

“Speakers Type” is set to “Bi-Amp” (see page 47).

• This procedure can also be performed on the AV

receiver/AV amplifier by using its [MULTI CH] but-

ton.

You can adjust the bass and treble for the front speakers,

except when the Direct, Pure Audio or THX listening

mode is selected.

■ Bass

You can boost or cut low-frequency sounds output by the

front speakers from –10 dB to +10 dB in 2 dB steps.

■ Treble

You can boost or cut high-frequency sounds output by

the front speakers from –10 dB to +10 dB in 2 dB steps.

Notes:

• This setting is not available when the multichannel

DVD input is selected.

• This procedure can also be performed on the remote

controller by using [AUDIO] button (see page 85).

You can display various information about the current

input source as follows.

Note:

This procedure can also be performed on the AV

receiver/AV amplifier by using its [DISPLAY] button.

The following information can typically be displayed for

input sources.

* If the input signal is analog, no format information is displayed.

If the input signal is PCM, the sampling frequency is displayed.

If the input signal is digital but not PCM, the signal format and

the number of channels is displayed. For some digital input sig-

nals, including multichannel PCM, the signal format, number of

channels, and sampling frequency is displayed.

Information is displayed for about three seconds, then the previ-

ously displayed information reappears.

You can adjust the brightness of the AV receiver/AV

amplifier’s display.

Using the Multichannel DVD Input

Remote

controller

Press the [MULTI CH] button.

“Multich” appears on the display.

Audio from the multichannel DVD

input will now be used for the DVD

input source.

Adjusting the Bass & Treble

AV receiver/

AV amplifier

Press the [TONE] button repeat-

edly to select either “Bass” or

“Treble”.

Use the Up [r] and Down [e]

buttons to adjust.

Displaying Source Information

Remote

controller

Press the [RECEIVER] button,

and then press the [DISPLAY]

button repeatedly to cycle

through the available informa-

tion.

Setting the Display Brightness

Remote

controller

Press the [RECEIVER] button,

and then press the [DIMMER]

button repeatedly to select:

• Normal + VOLUME light on.

• Normal + VOLUME light off.

• Dim + VOLUME light off.

• Dimmer + VOLUME light off.

Alternatively, you can use the AV

receiver/AV amplifier’s [DIMMER]

button (North American models and

TX-SA806 only).

Sampling

frequency

Input source

Signal format*

Listening

mode

TX-SR806_En.book Page 57 Monday, August 4, 2008 10:25 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR806 Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR806

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info