Bedienungsanleitung Onkyo TX-SR8260 (Seite 38 von 96) (Englisch)

645310

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Connecting the AV receiver

—Continued

The AV receiver has AC outlets on its rear panel that can

be used to connect the power cords of AV other compo-

nents that you intend to use with the AV receiver. These

components can then be left turned on so that they turn

on and off as and when the AV receiver is turned on and

set to Standby.

Caution:

• Make sure that the total capacity of the components

that you connect to the AC OUTLETS does not exceed

the stated capacity (e.g., TOTAL 120 W).

Note:

• Onkyo components with jacks should be con-

nected directly to wall outlets, not the AV receiver’s

AC OUTLETS.

• The number of AC OUTLETS, socket type, and total

capacity depends on the country in which you pur-

chased the AV receiver.

The TX-SR602/602E, TX-SR8260, American and Aus-

tralian TX-SR702 do not have this port.

This port can be used to connect an external controller

for controlling the AV receiver.

• Before connecting the power cord, connect all your

speakers and AV components.

•Turning on the AV receiver may cause a momentary

power surge that might interfere with other electrical

equipment on the same circuit. If this is a problem,

plug the AV receiver into a different branch circuit.

Notes:

• Pressing the remote controller’s [ON] button once will

turn on the AV receiver. Pressing it again will turn on

any components connected via .

• When the AV receiver is on Standby, it will turn on

automatically when any one of its input selector but-

tons is pressed.

Not for the American and Australian models:

• The AV receiver is shipped with the POWER switch in

the ON position ( ). When the power cord is con-

nected for the very ﬁrst time, the AV receiver will go

on Standby and the STANDBY indicator will light up.

•To completely shut down the AV receiver, set the

POWER switch to the OFF position ( ).

Connecting the Power Cords of Other

Components

Connecting the RS232 Port

Connecting the Power Cord

AC OUTLETS

120

V 60

SWITCHED

TOTAL 120W 1A MAX.

OUTLETS

AC 230

240

V 50

SWITCHED

TOTAL 100

W MAX.

European and some

Asian models

American model

Turning On the AV receiver

Set the [POWER] switch to the

ON position ( ).

(Skip this step if you have the American

or Australian model.)

The AV receiver enters Standby mode,

and the STANDBY indicator comes on.

Note:

• The remote controller has no effect

while the [POWER] switch in the

OFF position.

Press the [STANDBY/ON] button.

Alternatively, press the remote

controller’s [RECEIVER] button

followed by the [ON] button.

The AV receiver comes on, the display

lights up, and the STANDBY indicator

goes off.

To turn off the AV receiver, press the

[STANDBY/ON] button. The AV

receiver will enter Standby mode.

STANDBY/ONSTANDBY/ON

POWER

STANDBY

• American &

Australian

models

• Other

models

POWER

OFFON

STANDBY

Remote

controller

TX-NR702,602_En.book Page 38 Monday, July 26, 2004 11:05 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR8260 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info