Bedienungsanleitung Oplink TripleShield (Seite 3 von 17) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

631680

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

Assemble the OPU station and connect to a

DHCP-enabled router

Assemble the system according to the provided picture. It

is recommended that the OPU be placed on a 3-5ft (0.91-

1.52m) high platform.

Note: Once the OPU is up and running, to establish proper connection to it,

power up the remaining devices within 5 feet of the OPU. When connection

is established and working, the devices can be moved to their desired

locations.

Activation completed

When you see the "System is ready!" message, your system

is ready for use.

Note: Your IP Camera status will be updated after 10 minutes.

Power up the IP Camera

Plug the IP Camera into an outlet within 5 feet of the OPU

to establish connection. Once connection is established

and working, the IP Camera can be moved to its desired

location.

Note: Should the placement of the camera cause the image to be upside-

down, use the Flip feature in the App to correct this matter. Video > Single

Video Mode > Image Setting.

Place the Door/Window Sensor

Each Door/Window Sensor set consists of two pieces. Take

the larger piece and with slight force, push the small tab on

the back plate outward and slide the back plate upward.

Remove the back plate and insert a battery into each Door/

Window Sensor set. Apply the double-sided tape to each

piece. It is recommended that the Door/Window Sensor be

mounted in a vertical/upright position.

Power up the Siren

Plug the Siren into an outlet within 5 feet of the OPU to

establish connection. Once connection is established and

working, the Siren can be moved to its desired location.

Your Siren comes with a backup battery pre-installed. To

make use of the backup battery, pull and remove the clear

plastic strip to initiate battery contact.

The camera can be

moved and mounted

after the initial activation.

Note: When the activation process

cannot be completed normally, the

App will ask you to scan the OPU's

QR code, located on the back of the

OPU, to continue.

Start devices activation on the app

Tap the"Activate Now" button. (Activation process takes

approximately 2 minutes)

Internet

Router

(Not included)

1/4 de pouce

(0,64 cm)Max

Montez le capteurde porte

Montez le capteur de Fenêtre

(G) Installaon des baeries des

capteurs de porte/fenêtre

1/4 de pouce

(0,64 cm)Max

Montez le capteurde porte

Montez le capteur de Fenêtre

(G) Installaon des baeries des

capteurs de porte/fenêtre

1/4 de pouce

(0,64 cm)Max

Montez le capteurde porte

Montez le capteur de Fenêtre

(G) Installaon des baeries des

capteurs de porte/fenêtre

Note: For the Door/Window Sensor, it does not matter

which piece you place on the frame and which piece

you place on the moving part. To creat proper contact,

ensure the tops of the two pieces line up. The Spacer is

used in situations where the smaller piece needs to be

elevated to the larger piece to ensure proper contact.

Place the Motion Sensor

Lift the top tab to remove the cover and install the battery

into the Motion Sensor. For maximum coverage, the

sensor should be placed in the corner of the room to be

monitored and no more than 7 feet above the ground. The

Motion Sensor is most eective in areas such as hallways

and entry points where possible intruders will have to pass

through.

Note: Once Motion sensor alarms, it will start

to count 3 minutes, and count over again if

any movement detected in this period .The

next alarm will be triggered only when no

movement is detected within 3minutes.

(H) Installaon des baeries

du capteur de mouvement

Montez le Capteur

de Mouvement

(H) Installaon des baeries

du capteur de mouvement

Montez le Capteur

de Mouvement

Congratulations!

You have successfully installed

the security system!

Smart PlugPanic ButtonRemote

Control

Siren Motion Sensor

Door/Window

Sensor

IP Camera

(E)

(F)

(A)

( I )

(D)

(C)

(B)

Add-on Devices

STEP

Installation Guide

(Sample of QR Code)

1/4 inch Max

Mount Door Sensor Mount Window Sensor

(G) Door/Window Sensor

Battery Installation

(H) Motion Sensor Battery

Installation

Mount Motion Sensor

Less than 7 Feet

Installationsanleitung Step Guide

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oplink TripleShield Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oplink TripleShield

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info