Bedienungsanleitung Optoma HQView-500 Series (Seite 19 von 35) (Englisch)

492720

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

T:+44 1274 394125 F: +44 1274 730960 E: techsupport@calibreuk..com 15

3.5.2. Output Mode

Settings: 640x480, 800x600, 1024x768, 1280x768, 1280x800, 1280x1024, 1360x768, 1366x768,

1400x1050, 1440x900, 1600x1200, 1680x1050, 1920x1200, 480i, 576i, 480p, 576p, 1080i, 720p,

1080p

Set up the desired output resolution with output mode. The output mode setting should match the

native resolution of the imaging device to avoid double scaling.

The 3GSDI output does not feature the PC mode resolutions, only 480i/p, 576i/p, 720p and 1080i/p

output modes are supported. Available SDI output modes are indicated by an SDI connector symbol in

the output mode selection list box of the OSD. SDI output modes not supported are indicated with this

symbol crossed out red.

The default output resolution as set by the factory or after a user issued factory reset is 640x480. If

only a SDI capable monitor is connected no image is displayed and consequently the output resolution

cannot by changes through the OSD. Pressing the Menu/Contrast up/Contrast down key combination

will switch the output resolution from 640x480 to 480i which SDI monitors should be capable to display.

If a DVI or VGA monitor has issues to display this 480i mode, by pressing the key combination again

the 640x480 output mode is set-up which all DVI and VGA monitors should be capable to display.

3.5.3. Location

Settings: Front Tabletop, Front Ceiling, Rear Tabletop, Rear Ceiling

The image can be flipped to accommodate different projection scenarios as well as screens mounted

upside down.

3.5.4. Frame Rate

Settings: 60 Hz, 50 Hz, 48 Hz, 24 Hz, Auto

In auto mode the output frame rate follows the input frame rate as configured in the Output Config

menu. Signals with 24Hz, 25H, 48Hz, 50Hz (plus margin) input modes get special treatment, modes

with other refresh rates are displayed at 60Hz. 24Hz input modes will be output at 24Hz if the output

resolution is set to either 720p or 1080p and the Frame Rate setting in the Output Config menu

includes 24Hz, otherwise it is displayed at twice the rate if the Frame Rate setting in the Output Config

menu includes 48Hz. Otherwise a 24Hz input mode is displayed at 60Hz. 48Hz input modes will be

output at 48Hz if the Frame Rate setting in the Output Config menu includes 48Hz. Otherwise it is

displayed at 50Hz. A 25Hz input mode is output at twice the frame rate 50Hz. An exception to the

24/25Hz input mode treatment is if the output resolution is set to 480i or 480p. 480i and 480p are

always run at 60Hz output rate. 50Hz input modes are displayed at 50Hz output rate.

The output frame rate can also manually set to 24Hz, 48Hz, 50Hz or 60Hz if possible, i.e. such output

modes are available. Only 720p and 1080p output modes are available with 24Hz refresh rate. 480i

and 480p output modes are only available at 60Hz refresh rate. For all other modes 48Hz, 50Hz and

60Hz refresh rate is available.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Optoma HQView-500 Series Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info