2
EN
! CAUTION - SETTING UP
The from
dampness,
gasses or other inammable or explosive liquids.
The
earth (grounded).**Avoid using dangerous extension cables.
**GROUNDING INSTRUCTIONS.
A. event or breakdown, a path
resistance
with cord equipment-grounding grounding
plug. The plug must be plugged
grounded in accordance with all local codes and ordinances.
Do
installed by a qualied electrician.
Improper
electric
with If repair or
replacement
grounding conductor to a live terminal.
Check with
are if in doubt as to whether the tool is properly
grounded.
Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole
receptacles accept tool’s cord
immediately
B.
nominal
outlet
plug
which
this plug
not available.
outlet
the
as a properly grounded outlet box.
GROUNDING PIN
COVER OF
GROUNDING
OUTLET BOX
MET
ADAPTER
GROUNDING MEANS
Grounding methods
2. GENERAL INFORMA
The manufacturer is not liable for damages in the following cases:
- failed observance of the instructions given herein;
- use of the machine other than that described in the “INTENDED USE” section;
-
workplace;
- Incorrect installation;
- lack of scheduled maintenance;
- modications or jobs that are not authorized by the manufacturer;
- use of non-original or inadequate spare parts;
- repairs that are not carried out by a specialist.
3. W
The
under warranty will only be accepted if they are backed-up by the copy of the
purchase document (bill or receipt).
The guarantee becomes void if:
a)
the machine has been tampered with;
b) the machine has not been used according to this manual;
c)
other parts that are not authorized by the manufacturer;
d)
in the rating nameplate.
4. USING
The
manufacturer reserves
necessary at any time.
It
of the manufacturer
The owner’s
so that it can be consulted whenever need be.
If
or an authorized service centre for another copy
The
a later date.
5. DEFINITIONS
Skilled :
is trained to carry out extraordinary maintenance jobs and repairs on the machine.
6. SYMBOLS
This symbol
provisions and instructions are not complied with.
This
he uses the machine.
This symbol points out that
he uses the machine.
This symbol points out the correct running direction of the machine
(grinding wheel).
7. TECHNICAL DA
Model 51
V 120V~ 60Hz
Rated power 300W
Grinding wheel dimensions
Outside Ø :
Inside Ø:
Thickness:
5 3/4” (145 mm)
7/8” (22,2 mm)
1/8” (3.2mm)
3/16” (4.7mm)
5/16” (8.0 mm)
Maximum speed of grinding wheel 3400 min
-1
Max. power of lamp 15W
Acoustic pressure level 77 dB(A)
Level of vibrations on operating handle < 2,5 m/s
2
T
sharpened
1/4” - .325” - 3/8” - .404” - 3/4”
Weight (complete machine) 13.25 pounds (6 kg)
8. P
1 Base unit 11 Arm operating handle
2 Arm-motor unit 12 Shield guard
3 Vise assembly 13 Arbor shield
4 Chain blocking handle 14 Grinding wheel
5 Vise adjustment knob 15 Sharpening depth adjustment knob
6 Chain jaws 16 Lock pin
7 Chain blocking unit adjustment knob 17 Lamp
8 Chain blocking unit adjustment knob 18 Main ON/OFF switch
9 Chain blocking unit 19 Electrical power cable
10 Arm blocking handle 20 Rating nameplate
9. SAFETY DEVICES
The grinder is equipped with the safety devices illustrated hereafter:
- Shield they
come away during the sharpening process.
These guards must always be tted in place when the machine is in use.
Always
be compromised if the guards are damaged and/or cracked.
- Switch: the
sudden power failure, the switch trips automatically and disconnects the machine
from
restored. Y
- Lock pin: this is used to block the arm in the completely raised position.
When the pin is loosened, the arm -
justing the sharpening angles, when replacing and dressing the grinding wheel.
When
the sharpening process.
10.
This machine is an electrical grinder for chains used in chain saws.
- Use
chart.
- Do not use the machine to cut or grind anything other than the chains envisaged.
- Secure the machine rmly to the bench or wall.
- The machine must not be used in corrosive or explosive environments.
- Any other use is to be considered improper
The
the machine.
P00801046_R05_511AX.indd 2 12/06/2009 9.02.11
