Bedienungsanleitung Oregon Scientific BAR628HGU (Seite 5 von 8) (Englisch)

461269

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

3. Set the channel. The switch is located in the battery

compartment.

4. Place the sensor near the main unit. Press RESET

on the sensor. Then, press and hold MEM and

CHANNEL on the main unit to initiate signal sending

between the sensor and the main unit. The reception

icon on the main unit will blink for approximately 3

minutes while it is searching for the sensor. (Refer to

the "Sensor Data Transmission" section for more

information.)

5. Close the remote sensor battery compartment.

6. Secure the sensor in the desired location using the

wall mount or table stand.

For best results:

•Insert the batteries and select the channel before

you mount the sensor.

•Place the sensor out of direct sunlight and moisture.

• Do not place the sensor more than 30 metres

• (98 feet) from the main (indoor) unit.

• Position the sensor so that it faces the main

(indoor) unit, minimizing obstructions such as

doors, walls, and furniture.

•Place the sensor in a location with a clear view to

the sky, away from metallic or electronic objects.

• Position the sensor close to the main unit during

cold winter months as below-freezing temperatures

may affect battery performance and signal

transmission.

You may need to experiment with various locations to

get the best results.

DATA TRANSMISSION

Data is sent from the sensor(s) every 40 seconds. The

reception icon shown in the Temperature and Humidity

Areas show the status.

SEARCH FOR SENSOR

To search for a sensor, press and hold MEM and

CHANNEL (on the main unit) for 2 seconds.

NOTE If the sensor is still not found, check the batteries,

obstructions, and remote unit location.

NOTE Signals from household devices such as doorbells,

electronic garage doors, and home security systems

may cause temporary reception failure. This is normal

and does not affect general product performance. The

reception will resume once the interference ends.

CLOCK

The clock automatically synchronizes the current time

and date when it is brought within range of the radio

signal DCF77 generated from Frankfurt, Germany for

Central Europe (model BAR628HG) or MSF60 generated

from Rugby, England (model BAR628HGU).

NOTE The signals are collected by the main unit when

it is within 1500 km (932 miles) of a signal.

Initial reception takes 2-10 minutes, and is initiated when

you first setup the unit, and whenever you press RESET.

Once complete, the reception icon will stop blinking. The

icon is shown in the Clock Area.

To force a manual search for clock signals, press and

hold

for 2 seconds. If no signal is found, check the

batteries.

TURN CLOCK ON / OFF

Perform this step if you cannot receive clock signals.

Press and hold

for 2 seconds. Then, manually set the

clock following the “Set Clock” instructions (below).

The signal icon indicates that the clock feature is ON.

No icon means that it is OFF.

SET CLOCK / CALENDAR

You only need to do this if you have disabled the clock

feature (for example, if you are too far from or cannot

receive a signal).

1. Press and hold MODE for 2 seconds. The Clock Area

will blink.

2. Select the hour, minute, year, month, day, and day of

the week language. Press

or to change the

setting.

3. Press MODE to confirm.

The language options are (E) English, (F) French, (D)

German, (I) Italian, and (S) Spanish.

Strong signal Weak signal No signal

ICON DESCRIPTION

Main unit is searching for

sensons.

At least 1 channel has been

found.

Channel 1 is selected (number

will change depending on the

sensor you select)

...shows in Outdoor The selected sensor cannot

Temp / Humidity Area be found. Search for the

sensor or check batteries.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oregon Scientific BAR628HGU Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oregon Scientific BAR628HGU

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info