Bedienungsanleitung Oregon Scientific BAR686A (Seite 1 von 2) (Englisch)

796423

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

INTRODUCTION

Thank you for selecting this Oregon ScienticTM Wireless

Weather Forecaster with Temperature Display and Self

- Setting Atomic Clock (BAR686A). This clock is supplied

with a remote sensor (THN122N) and can support up to 3

sensors in total (additional sensors sold separately).

NOTE Please keep this manual handy as you use your

new product. It contains practical step-by-step instructions,

as well as technical specications and warnings you should

know about.

CLOCK OVERVIEW

FRONT VIEW

1. SNOOZE

BACK VIEW

1. / : Increase / decrease setting; activate / deactivate

clock reception signal

2. CHANNEL: Switch remote sensor display

3. MODE: Change settings / display

4. ALARM: View alarm status; set alarm

5. Battery compartment

6. TEMP HI / LO : Change settings or enable / disable

hi or lo temperature alarm for channel 1

7. °C / °F: Select temperature unit

8. MEM: View current, maximum and minimum

temperature / humidity

9. RESET: Reset unit to default settings

LCD DISPLAY

1. Sensor battery low

2. Ice warning is active

3. Pressure trend

4. Weather Forecast

5. Alarm set

6. AM / PM mode selected

7. Clock signal reception

8. Clock

9. Sensor reception icon

10. Hi / lo temperature alarm

11. Outdoor temperature trend

12. Outdoor temperature

13. Max / Min icon

14. Main unit battery low

15. Indoor temperature trend

16. Indoor temperature

17. Max / Min icon

18. Main unit sensor icon

19. Alarm mode

20. Moon Phase

21. Day and Month display

REMOTE SENSOR (THN122N)

1. LED status indicator:

Blinks red during data

transmission

2. Ventilation duct

1. Wall mount hole

2. RESET hole

3. CHANNEL switch

4. Battery compartment

GETTING STARTED

SETTING UP THE CLOCK

Insert batteries before rst use, matching the polarity (+

and -). RESET after each battery change.

SENSOR DATA TRANSMISSION

indicates main unit batteries are low.

NOTE Do not use rechargeable batteries. We recommend

that you use alkaline batteries with this product for longer

usage and lithium batteries in temperatures below

freezing.

REMOTE SENSOR

3. Select a channel. Make sure you use a different channel

for each sensor.

4. Place the sensor near the main unit. Press RESET on

the sensor.

5. Simultaneously press CHANNEL and MEM on the main

unit to initiate signal sending between the sensor and

main unit.

6. Close the battery door and secure the screws.

7. Place the sensor in the desired location using the table

stand or wall mount.

For best results:

• Place the sensor out of direct sunlight and moisture.

• Do not place the sensor more than 30 m (100 ft) from

the main (indoor) unit.

• Position the sensor so that it faces the main (indoor)

unit, minimizing obstructions such as doors, walls, and

furniture.

• Place the sensor in a location with a clear view to the

sky, away from metallic or electronic objects.

• Position the sensor close to the main unit during cold

winter months as below-freezing temperatures may

affect battery performance and signal transmission.

The transmission range may vary depending on many

factors. You may need to experiment with various locations

to get the best results.

Standard Alkaline batteries contain signicant amounts of

water. Because of this they will freeze in low temperatures

of approximately -12°C (10°F). Disposable Lithium batteries

have a much lower threshold for temperature with an

estimated freezing range of below -30°C (-22°F).

Wireless ranges can be impacted by a variety of factors

such as extremely cold temperatures. Extreme cold may

temporarily reduce the effective range between the sensor

and the base station. If the unit's performance fails due to

low temperature, the unit will resume proper functioning

as the temperature rises to within the normal temperature

range (i.e. no permanent damage will occur to the unit due

to low temperatures).

Data is sent from the sensor(s) every 40 seconds. The

sensor reception icon in the remote sensor area shows

the status.

To search for a sensor:

Simultaneously, press and hold MEM and CHANNEL for

2 seconds.

NOTE If the sensor is still not found, check the batteries,

obstructions, and remote unit location.

CLOCK

CLOCK RECEPTION

This product is designed to synchronize its date and time

automatically once it is within range of the WWVB-60 signal

from the atomic clock in Boulder, Colorado.

RECEPTION SIGNAL

Clock signal reception indicator:

SET CLOCK

To manually set the clock make sure the clock signal

reception is disabled.

1. Press and hold MODE for 2 seconds.

2. Select the US time zone (Pacic (P), Eastern (E), Central

format, month, day and language. Press or to

change the setting.

3. Press MODE to conrm.

NOTE The language options are (E) English, (D) German,

(F) French, (I) Italian, and (S) Spanish.

Press MODE to choose between the clock with seconds

and clock with weekday display modes.

ALARM

To set the alarm:

1. Press and hold ALARM for 2 seconds.

2. Press / to set hour / minute.

3. Press ALARM or MODE to conrm. indicates alarm

is ON.

To toggle alarms ON / OFF:

1. Press ALARM to display alarm time.

2. Press ALARM again to turn alarm ON / OFF.

To silence the alarm:

• Press SNOOZE to silence it for 8 minutes.

• Press any key except SNOOZE to turn the alarm off

and activate it again after 24 hours.

WEATHER FORECAST

This product forecasts the next 12 to 24 hours of weather

within a 30-50 km (19-31 mile) radius based on barometric

pressure trend readings.

ICON DESCRIPTION

Clear

Cloudy

Rainy

Partially Cloudy

 







































The sensor collects temperature readings approx. every

40 seconds and sends them to the main unit. The main

unit can collect data from up to 3 sensors.

To set up the sensor:

1. Remove the screws from the battery door.

2. Insert the batteries, matching the polarity (+ / -).

The sensor collects the radio signals whenever it is within

1500 km (932 miles) of a signal.

NOTE Initial reception takes 2-10 minutes for rst set up

or when RESET is pressed. Once complete, the reception

icon will stop blinking. If the signal is weak, it can take up

to 24 hours to get a valid signal.

To enable and force a signal search:

Press and hold for 2 seconds.

To disable the signal reception:

Press and hold for 2 seconds.

ashes when it is disabled.

USER MANUAL

ICON DESCRIPTION

and “- - . -“

(Outdoor

temperature area)

The sensor cannot be found.

Search for the sensor or check

batteries

Sensor 1 is sending data

A channel has been found

Main unit is searching

for the sensor(s)

STRONG SIGNAL WEAK SIGNAL NO SIGNAL

Wireless Weather Forecaster with

Temperature Display and Self - Setting

Atomic Clock

MODEL: BAR686A

BAR686_M 2005.12.12, 4:36 PM1

Oregon Scientific BAR686A Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info