Bedienungsanleitung Oregon Scientific BAR898HG (Seite 10 von 17) (Englisch)

461272

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

minutes, the pre-alarm will start to operate at 6:15 am (45 minutes

before 7:00 am). The Pre-Alarm icon will flash and the backlight

will be turned on for 5 seconds. An alarm sound will also go off

for 2 minutes as that of the daily alarm and the snooze function

will also be activated if the [ SNOOZE / LIGHT ] button or stand-

button is pressed.

Note: The daily alarm will NOT function until the next day if the

pre-alarm has been triggered beforehand. Deactivation of the

alarm function will disable the pre-alarm feature automatically.

NOTE ON REMOTE READINGS

Once batteries are in place in the remote unit, it will start

transmitting samplings at 40-second intervals. If no signals are

received when the remote sensor display is selected, "--- " will be

displayed. To force the main unit to search for remote sensor

signals, press [ MEMORY ] and [ CHANNEL ] simultaneously.

If that fails, check that the remote sensor is still in place. Make

sure the transmission is within range and the path is clear of

obstacles and interference. Repeat this procedure whenever you

find discrepancies between the display on the main unit and the

display on the remote sensor.

CHECKING INDOOR AND REMOTE

TEMPERATURES & HUMIDITIES

To display the indoor and outdoor temperature and humidity

readings, press the [ CHANNEL ] button to toggle among the

indoor, Channel 1, 2 and 3 displays.

The temperature can be shown in Centigrade (°C) or Fahrenheit

(°F). Select the appropriate reading by using the [

°C / °F ] slide

switch (located in the battery compartment). Slide the switch to

°C for Centigrade or °F for Fahrenheit.

If the reading goes above or below the specified amounts, the

display will show a flashing "HHH" or "LLL".

This unit has an auto-scan function that can sequentially display

the indoor and remote readings. To activate this function, press

and hold the [ CHANNEL ] button for 3 seconds. To deactivate

press the [ CHANNEL ] button again.

NOTE ON °C AND °F

The outdoor temperature display on the main unit is dominated

by the selection on the [ °C / °F ] slide switch of the main unit.

Whatever the display unit of the remote sensor is, it will only

apply to the remote sensor itself and the temperature will be

automatically converted to the chosen one of the main unit.

MAXIMUM AND MINIMUM

TEMPERATURES & HUMIDITIES

The maximum and minimum recorded temperatures and

humidities will be automatically stored in memory. To display

them, press [ MEMORY ] . Press [ MEMORY ] again to alternate

between the maximum, minimum and current readings. The

respective MAX or MIN indicator will be displayed.

To clear the memory, press [ MEMORY ] and hold for three

seconds. The maximum and minimum recorded readings will be

BAR898-e R2 OP 8/21/04, 10:45 PM9

Black

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oregon Scientific BAR898HG Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oregon Scientific BAR898HG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info