Bedienungsanleitung Oregon Scientific ds 6688 (Seite 10 von 19) (Englisch)

287898

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

DS6688 Manual-Eng,Ita,Fre (086-003403-012)

DEESPORNLSWE

DS6688BSX1 Manual-Eng (086-003403-080)

1413

AUTO OFF (AUTO POWER-OFF)

You can set the camera to turn off automatically when no operation is

performed. The period of time before shut-down can be adjusted

(1 min., 3 min., or 5 min.) The default auto off time setting is 3 min.

NOTE: Auto Off is not available in slideshow mode or when the

camera is connected to a PC.

TV OUT

If connecting the camera to a TV, you can set the camera's TV output

system to either the PAL or NTSC standards. The default TV Out

setting is set to PAL.

FILE NUMBER

Your camera keeps an internal file counter for every image and movie

taken that can be reset. The setting options are Continue (default

setting) and New.

NOTE: All files are stored within a designated folder. The initial folder

is always numbered at 100.

A. Under the Continue default option, the internal file counter is first

set to "0001". Every subsequent picture is assigned an incremental

File Number.

NOTE: The internal file counter increments by 1 regardless of the

media unless it is reset.

B. Under the New option, the internal file counter to "0001" for new

media only. But in case there are image files already present inside

the storage media, it will start counting from the highest file number of

the media.

NOTE: The File Number setting should be set to New only if either the

internal memory or SD card has been newly formatted, or a completely

new SD card has been installed.

FORMAT

This option will format all data in either the internal memory or the

external SD card / MMC, including all protected files.

CAUTION: Do not eject the SD card / MMC while the card is being

formatted, as this may damage the card. Formatting deletes all data

from the memory device chosen. Files will not be recoverable.

RESET

You can reset all camera settings to factory default. Refer to the Setup

Menu table to see the defaults for each setting.

NOTE: The reset function can reset all the settings to factory default

except for the current time and date.

LCD BRIGHT (LCD BRIGHTNESS)

You can adjust the LCD brightness level to

compensate for different lighting conditions, for

example.

• If there is plenty of ambient light such as in

bright sunshine, you can adjust the brightness

levels higher to make the display easier to see.

• If ambient light levels are relatively low such as

indoors or at night, you can adjust the brightness

levels lower to make the display easier to see.

TIP: To maximize battery life, keep brightness settings low.

SYSTEM INFORMATION

This option allows you to check the camera model number and cur-

rent version of firmware installed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oregon Scientific ds 6688 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oregon Scientific ds 6688

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info