Bedienungsanleitung Oregon Scientific JM888 (Seite 5 von 9) (Englisch)

589262

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

GETTING STARTED

The sensor range is up to 30 meters (100 feet) with no

obstructions.

SEARCHING AND DISPLAYING THE UV DATA

To begin searching for remote signals from the UV

sensor, press and hold both the UP and DOWN buttons

simultaneously for more than 2 seconds. (The lower left

corner of the display will toggle between the temperature

and the UV reading when a UVI reading from a UV

sensor is detected).

NOTE The UV sensor must be activated beforehand.

Please refer to the UVR138 user manual for more

information.

UV INDEX DISPLAY

UV Index Level Icon Display

0 ~ 2 Low

3 ~ 5 Medium

6 ~ 7 High

8 ~ 10 Very high

11 ~ 25 Extremely high

NOTE When the index is calculated to be higher than

25, ““HH”” will blink.

TEMPERATURE READINGS

The temperature display range is from -20°C to +60°C.

The temperature beyond these limits will show ““LLL”” or

““HHH””.

CHANGING CELSIUS TO FAHRENHEIT

To change Celsius to Fahrenheit:

Simply slide the switch at the back of the clock from

°C

°F. (This switch is located inside the battery

compartment).

THE RESET HOLE

If the clock behaves strangely or stops responding,

insert and press a blunt stylus into the clock’s RESET

hole to reset the unit’s settings. (This is located inside the

battery compartment).

DEFAULT SETTINGS

All segments of the LCD will be turned on for 3 seconds

and a beep sound will be given out. Then it will start RF

reception.

• The clock settings are: PM12:00, 1st January 2004,

RF enabled, English.

• The clock displays in 24 / 12 hour mode depending

on the selection of the radio signal EU/UK.

SAFETY & CARE INSTRUCTIONS

SAFETY PRECAUTIONS

Please observe the following safety precautions when

setting up and using this product:

• LCD panel - The LCD panel is made of glass, and

may break if the unit is dropped or impacted.

• Heat sources - Keep the product away from heat

sources such as radiators, stoves, heaters, and

other heat-generating products.

CARING FOR YOUR PRODUCT

To ensure you receive the maximum benefit from using

this product, please observe the following guidelines:

• Cleaning - Use a damp cloth. Do not use liquid

cleaning agents, benzene, thinner, or aerosols.

• Ventilation - The vents and other openings are

designed for ventilation, and should not be blocked

or covered.

• Blocking the vents can cause the product to overheat,

and can damage the unit.

• Repair - Do not attempt to repair the product or

modify the circuitry by yourself. Contact the retailer

or a qualified repairman if the product requires

servicing. Only use replacement parts that are

recommended by the manufacturer.

• Do not scratch hard objects against the LCD display

as this may cause damage.

JM888_EN_R8 03/09/2004, 17:055

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oregon Scientific JM888 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oregon Scientific JM888

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info