Bedienungsanleitung Oregon Scientific RMR803 (Seite 1 von 2) (Englisch, Französisch, Spanisch)

796536

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Solar Indoor / Outdoor Thermometer

with Indoor Hygrometer and

Atomic Clock

Model: RMR803 / RMR803A

USER MANUAL

OVER VIEW

FRONT VIEW (FIG 1)

1. Solar panel

2. Remote sensor reception indicator

3. Clock signal reception indicator

4. MODE: Change settings / display

5. LIGHT: Activate backlight for 5 seconds

6. / : Increase / decrease value; activate /

deactivate clock reception signal; : toggle between

outdoor channels (1-3)

7. Outdoor temperature

8. Indoor temperature and humidity

9. Time zone (RMR803A only)

10. Clock with weekday

11. MEM: View current, maximum, minimum temperature /

indoor humidity

12. Ice alert LED indicator

BACK VIEW (FIG 2)

EU UK

1. °C / °F: Select temperature unit

2. EU / UK: Select the nearest radio signal (RMR803 only)

3. RESET: Reset unit to default settings

REMOTE SENSOR (FIG 3)

1. LED status indicator

2. Wall mount hole

3. Battery compartment

4. RESET hole

5. CHANNEL switch

GETTING STARTED

SOLAR PANEL

The solar panel is an energy saving feature, which is an

environmentally friendly way to provide additional power to

the main unit and prolongs battery life. However, it cannot

replace battery power entirely.

INSERT BATTERIES

1. Remove the battery compartment.

2. Insert the batteries, matching the polarities (see FIG 2).

LOCATION MEANING

Clock Main unit batteries low

Outdoor temperature Sensor batteries low

REMOTE SENSOR

The main unit can collect data from up to 3 sensors.

To set up the sensor:

1. Open the battery compartment (see FIG 3).

2. Insert the battery, matching the polarities.

3. Select a channel then press RESET.

4. Close the battery door.

5. Place the sensor within 30 m (98 ft) of the main unit

using the table stand or wall mount.

TIP Ideal placements for the sensor would be in any

location on the exterior of the home at a height of not more

than 1.5 m (5 ft) and which can shield it from direct sunlight

or wet conditions for an accurate reading.

1.5 m (5 ft)

NOTE Use alkaline batteries for longer usage and consumer

grade lithium batteries in temperatures below freezing.

SENSOR DATA TRANSMISSION

To search for a sensor:

Press and hold + MODE.

The sensor reception icon in the remote sensor area shows

the status:

ICON DESCRIPTION

Main unit is searching for sensor(s).

A channel has been found.

The sensor cannot be found.

TIP The transmission range may vary depending on many

factors. You may need to experiment with various locations

to get the best results.

CLOCK

CLOCK RECEPTION

This product is designed to synchronize its clock automatically

with a clock signal.

RMR803:

Slide EU / UK to select the signal received.

• EU: DCF-77 signal: within 1500 km (932 miles) of

Frankfurt, Germany.

• UK: MSF-60 signal: within 1500 km (932 miles) of

Anthorn, England.

RMR803A:

• WWVB-60 signal: within 3200km (2000 miles) of Fort

Collins, Colorado.

To enable / disable signal reception:

Press and hold to enable or to disable signal

reception.

NOTE Reception takes 2-10 minutes. If the signal is weak,

it can take up to 24 hours to get a valid signal. If signal

reception is unsuccessful, place your unit next to a window,

press and hold to force another signal search.

Clock signal reception indicator:

STRONG SIGNAL WEAK / NO SIGNAL

MANUALLY SET CLOCK

To set the clock manually, disable the signal reception ﬁrst.

1. Press and hold MODE.

2. Press or to change the settings.

3. Press MODE to conﬁrm.

4. The settings order is: time zone, 12/24 hr format, hour,

minute, year, calendar mode (day – month / month –

day), month, day and language.

RMR803: Time zone offset sets the clock +/- 23 hours from

the received clock signal time.

RMR803A: Select the time zone: (P) Paciﬁc, (E) Eastern, (C)

Central or (M) Mountain.

NOTE The language options are English (E), German (D),

French (F), Italian (I), Spanish (S) and Russian (R).

To select display mode:

Press MODE to choose between clock with seconds, clock

with weekday or calendar.

TEMPERATURE AND HUMIDITY

To toggle temperature unit:

Press °C / °F.

To toggle between each outdoor sensor’s readings:

Press repeatedly.

Press and hold + MEM for 2 seconds to initiate auto

toggle of outdoor channels.

To end press .

To toggle between current, minimum and maximum

records:

Press MEM repeatedly.

To clear the records:

Press and hold MEM.

ICE WARNING

If the sensor falls between 3°C to -2 °C (37°F to 28°F), the

green LED indicator will ﬂash, and will stop ﬂashing once the

temperature is out of this range.

NOTE As ice alert is only applicable to channel 1, to prevent

ﬂashing of LED, select channel 2 or 3 on outdoor sensor.

BACKLIGHT

Press LIGHT to activate backlight for 5 seconds.

RESET

Press RESET to return to the default settings.

PRECAUTIONS

• Do not subject the unit to excessive force, shock, dust,

temperature or humidity.

• Do not cover the ventilation holes with any items such as

newspapers, curtains etc.

• Do not immerse the unit in water. If you spill liquid over

it, dry it immediately with a soft, lint-free cloth.

• Do not clean the unit with abrasive or corrosive

materials.

• Do not tamper with the unit’s internal components. This

invalidates the warranty.

• Only use fresh batteries. Do not mix new and old

batteries.

• Images shown in this manual may differ from the actual

display.

• When disposing of this product, ensure it is collected

separately for special treatment.

• Placement of this product on certain types of wood

may result in damage to its ﬁnish for which Oregon

Scientiﬁc will not be responsible. Consult the furniture

manufacturer's care instructions for information.

• The contents of this manual may not be reproduced

without the permission of the manufacturer.

• Do not dispose old batteries as unsorted municipal

waste. Collection of such waste separately for special

treatment is necessary.

• Please note that some units are equipped with a

battery safety strip. Remove the strip from the battery

compartment before ﬁrst use.

NOTE The technical speciﬁcations for this product and the

contents of the user manual are subject to change without

notice.

NOTE Features and accessories will not be available in all

countries. For more information, please contact your local

retailer.

SPECIFICATIONS

TYPE DESCRIPTION

MAIN UNIT

L x W x H 73 x 38 x 132 mm

(2.87 x 1.50 x 5.20 in)

Weight 170 g (6 oz) without battery

Temperature range -5°C to 50°C (23°F to 122°F)

Signal frequency 433 MHz

Indoor humidity range 25% - 95%

Power 2 x UM-3 (AA) 1.5 V batteries

REMOTE UNIT (THN132N)

L x W x H 96 x 50 x 22 mm

(3.78 x 1.97 x 0.87 in)

Weight 62 g (2.22 ounces)

Transmission range 30 m (98 ft) unobstructed

Temperature range -20°C to 60°C (-4°F to 140°F)

Power 1 x UM-3 (AA) 1.5 V batteries

ABOUT OREGON SCIENTIFIC

Visit our website (www.oregonscientiﬁc.com) to learn more

about Oregon Scientiﬁc products. If you’re in the US and

would like to contact our Customer Care department directly,

please visit: www2.oregonscientiﬁc.com/service/support.asp

For international inquiries, please visit: www2.oregonscientiﬁc.

com/about/international.asp

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) This

device must accept any interference received, including

interference that may cause undesired operation.

WARNING Changes or modiﬁcations not expressly

approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

NOTE This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference

in a residential installation.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV

technician for help.

DECLARATION OF CONFORMITY

The following information is not to be used as contact

for support or sales. Please visit our website at www2.

oregonscientiﬁc.com/service for all enquiries.

Name: Oregon Scientiﬁc, Inc.

Address: 19861 SW 95th Ave.,Tualatin,

Oregon 97062 USA

Telephone No.: 1-800-853-8883

declare that the product

Product No.: RMR803 / RMR803A

Product Name: Solar Indoor / Outdoor

Thermometer with Indoor

Hygrometer and Atomic Clock

Manufacturer: IDT Technology Limited

Address: Block C, 9/F, Kaiser Estate,

Phase 1,41 Man Yue St.,

Hung Hom, Kowloon,

Hong Kong

is in conformity with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: 1) This device may

not cause harmful interference. 2) This device must accept

any interference received, including interference that may

cause undesired operation.

Solaire thermomètre intérieur /

extérieur avec hygromètre intérieur

et heure atomique

Modèle : RMR803 / RMR803A

MANUEL DE L’UTILISATEUR

VUE D’ENSEMBLE

FACE AVANT (FIG 1)

1. Panneau solaire

2. Indicateur de réception de la sonde à distance

3. Indicateur de réception du signal de l’horloge

4. MODE : Changez les réglages / l’afﬁchage

5. LIGHT : Permet d’activer le rétro-éclairage pendant 5

secondes

6. / : Augmente / diminue les réglages ; active /

désactive le signal de réception de l’horloge; : permet

d’alterner entre les canaux extérieurs (1-3)

7. Température extérieure

8. Température et humidité intérieure

9. Fuseau horaire (modèle RMR803A seulement)

10. Horloge avec les jours de la semaine

11. MEM: Afﬁchage de la température et de l’humidité

intérieure actuelle/maximum/minimum

12. Indicateur LED d’alarme de gel

FACE ARRIÈRE (FIG 2)

EU UK

1. °C / °F: Sélectionner l’unité de mesure de température

2. EU / UK : Sélectionne le signal radio le plus proche

(modèle RMR803 seulement)

3. REINITIALISER (RESET) : Réinitialiser l’appareil aux

réglages par défaut

SONDE SANS FIL (FIG 3)

1. Indicateur d’état LED

2. Trou de ﬁxation murale

3. Compartiment des piles

4. Fente REINITIALISER (reset)

5. Bouton CANAL (channel)

POUR COMMENCER

PANNEAU SOLAIRE

Le panneau solaire est un accessoire permettant

d’économiser l’énergie, c’est une façon écologique de

fournir de l’électricité supplémentaire à l’appareil principal

prolongeant la durée de vie de la pile. Il ne peut cependant

remplacer entièrement l’alimentation par piles.

INSÉREZ LES PILES

1. Retirez le couvercle du compartiment des piles.

2. Insérez les piles en respectant les polarités. (voir FIG 2).

EMPLACEMENT SIGNIFICATION

Horloge Piles faibles de l’appareil

principal

Zone de température

extérieure Piles faibles du capteur

SONDE SANS FIL

L’appareil principal est à même de collecter les données de

3 sondes maximum.

Pour installer le capteur :

1. Ouvrez le couvercle du compartiment des piles. (voir FIG 3).

2. Insérez les piles, en respectant les polarités.

3. Sélectionnez un canal puis appuyez sur RESET.

4. Fermez le couvercle du compartiment des piles.

5. Installez le capteur à 30 m maximum (98 pieds) de

l’appareil principal à l’aide du support de table ou de la

ﬁxation murale.

CONSEIL Les emplacements idéaux pour le capteur

sont dans tout endroit extérieur à l’habitat, à une hauteur

ne dépassant pas les 1.5 m (5 pieds) et permettant de le

protéger contre la lumière directe du soleil ou de conditions

humides, aﬁn d’obtenir une lecture précise.

1.5 m

(5 pieds)

REMARQUE Utilisez des piles alcalines pour un usage

prolongé et des piles au lithium pour la consommation lors

de basses températures (gel).

TRANSMISSION DES DONNÉES DU CAPTEUR

Pour rechercher un capteur :

Appuyez et maintenez la touche + MODE.

L’icône de réception du capteur située dans la zone de la

sonde à distance, indique l’état:

ICONE DESCRIPTION

L’appareil principal est à la

recherche du/des capteur(s).

Un canal a été trouvé.

Le capteur est introuvable.

RMR803A_US_R2.indd 1 2009.4.23 10:32:02 AM

Oregon Scientific RMR803 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info