Bedienungsanleitung Oregon Scientific SE331 (Seite 8 von 113) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

796550

Zoom out

Zoom in

Vorherige Seite

1/113

Nächste Seite

1. Press +/ST/SP and proceed to use the watch as a

stopwatch (without exercise recording function); or

2. Press MODE/- to force another signal search.

Analog or Digital?

The digital signal is less susceptible to signal interference

and is suitable in crowded areas or where there are other

monitors / equipment. You should only switch to the analog

transmission signal if the situation in point 2 occurs (see

‘Encountering difculties?’ below).

To switch from digital to analog or

analog to digital system:

1. Press the chest belt button for

more than 6 seconds.

2. Press and hold MODE/- on the

watch to force a signal search.

Encountering difculties?

In the event that you experience a weak signal or your signal

is disrupted by interference in the environment, follow the

instructions below to identify and resolve the situation.

1. The signal is weak - the watch may only show “--”:

• Shorten the distance between the heart rate chest

belt and watch.

• Re-adjust the position of the heart rate chest belt.

• Check the conductive pads are moist enough to

ensure solid contact.

• Check the batteries. If they are low or exhausted, the

transmission range may be shortened.

• Press and hold MODE/- to force a signal search.

2. The gym equipment does not seem to work with your

chest belt and the digital icon is displayed:

• Most gym equipment is compatible with the analog

system . Press and hold the chest belt button

for more than 6 seconds to change from digital to

analog. Then press and hold MODE/- to force a

signal search.

3. Interference from another person’s heart rate monitor -

their heart rate readings appear on your watch, or the

readings may uctuate:

• Force another signal search by pressing the chest

belt button then press and hold MODE/- on the

watch. Do not press and hold the chest belt button,

as it will change the transmission signal from digital

to analog.

4. The signal is jammed - “NO HR BELT” appears on the

display after several tries:

• There is too much interference in the environment

for your heart rate monitor to function. Move to an

area where the watch can register your heart rate

reading.

WARNING Signal interference in the environment can be

caused by electromagnetic disturbances. These may occur

near high voltage power lines, trafc lights, overhead lines

of electric railways, electric bus lines or trams, televisions,

car motors, bike computers, some motor driven exercise

equipment, cellular phones or when you walk through

electric security gates. Under interference, the heart rate

reading may become unstable and inaccurate.

START EXERCISING

If you wish to receive comprehensive calculations (such as

your heart rate and the calories / fat burnt) for an exercise

session, before you start, allow the watch a few seconds

to search for chest belt rst. For detailed information or

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oregon Scientific SE331 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info