Bedienungsanleitung Oregon Scientific TD339 (Seite 6 von 31) (Englisch)

587045

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

ENG

SETTING UP YOUR TELEPHONE

Unpacking the telephone

When you unpack your ThermoDECT phone, make sure to keep all the packing materials in a safe

place, in case you need to later transport the phone or return it for servicing.

In the box, you will find:

• The ThermoDECT phone base unit

• The ThermoDECT phone cordless handset

• Two rechargeable batteries for the handset

• A 220-volt AC power cord

• A telephone line

• An attachable belt clip for the handset

• A remote temperature sensor

• Two regular batteries for the remote sensor

Choosing a location for the base unit

When selecting a location for your base unit, observe the following guidelines:

• Choose a location that provides easy access to a 220-volt AC power source. Never try to

lengthen the power cord. Use an appropriate AC power cord for your local power supply.

• Choose a location that will allow the telephone cable to reach a telephone jack. You can use an

extension jack or cable if necessary.

• Place the base unit as high as possible to obtain the maximum radio frequency range with the

handset. You may need to try several locations – such as upstairs, or near a first-floor landing –

to find the best range. Solid structures such as walls and doors may reduce the signal strength.

• Do not place the base unit near the sink, bathtub, or shower.

• Do not place the base unit near objects that may cause radio interference, such as another

telephone, large metal objects such a mirror or filing cabinet, or electrical appliance such as an

electric stove, washing machine, microwave oven, television, and fluorescent lights.

• Do not place the unit near heat sources such as radiators or air ducts, or in a place subject to

direct sunlight.

• The indoor temperature reading displayed is the temperature recorded at the base unit.

Connecting the base unit

To set up the base unit:

1.Plug the small end of the telephone cord

into the telephone socket located at the

back of the base unit, as shown in the

diagram to the right.

2.Plug the other end of the telephone cord

into the telephone wall socket.

3.Plug the small end of the AC power cord into the power socket located at the back of the base unit.

4.Plug the other end of the AC power cord into a nearby AC wall socket.

Installing the handset batteries

Your ThermoDECT telephone is shipped with two rechargeable Ni-MH batteries (AAA

size). To install the batteries:

1.Open the battery compartment located at the back of the handset unit.

2.Insert the batteries as shown in the diagram to the right, matching

positive (+) polarity to positive, and negative (-) polarity to negative.

Note: Reversing the polarity may damage the handset.

3.Replace the battery compartment by sliding it in the direction shown by the

arrow in the diagram to the right. The lid clicks into place when it is secure.

To phone

wall jack

To AC wall

A. LED indicator

Flashes when the

remote sensor

transmits a

temperature reading.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oregon Scientific TD339 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oregon Scientific TD339

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info