Bedienungsanleitung Oregon Scientific TD339 (Seite 21 von 31) (Englisch)

587045

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

ENG

Using the call waiting feature

If you receive an external call while you are talking to someone through the intercom, you will hear a

call waiting tone. To answer the incoming call:

1. Press the

button to terminate the intercom call.

Result: The external call rings.

2. Press

again to answer the external call.

Transferring calls between handsets

You can transfer an external call from one handset to another if you have registered more than one

handset with your ThermoDECT telephone. To transfer a call:

1. During a telephone conversation, press the

button to place the caller on hold.

2. Enter the handset number (1 – 5) to which you wish to transfer the call.

Result: The handset you paged rings, with EXT and INT flashing on the LCD display. The internal

party can answer the call by pressing the

button.

3. (Optional) Hang up the telephone to transfer the call once someone answers. If no one answer,

press

to terminate the page and return to the caller.

MONITORING THE TEMPERATURE

The temperature is shown on the handset display area, and on the LCD display for

the base unit. You can choose to display the temperature in celsius or Fahrenheit

degrees.

Changing from Celsius to Fahrenheit

To change the temperature display, insert an unfolded paperclip into the C/ F

hole located on the underside of the base unit, as shown in the diagram on this

page. Gently push to toggle the temperature display from one unit of measurement to the other.

You can choose to display the Indoor temperature as measured at the location of the base unit.

Monitoring the Indoor Temperature

The LCD display on the base unit shows you which temperature reading is displayed on both the base and

handset.

To select the Indoor Temperature, press the “Temp” button until “IN” appears on the base display. The base

and handset now display the Indoor temperature. It may take a few minutes for the handset display to be

updated.

Monitoring the Outdoor Temperature

In order to monitor the outdoor temperaturee, the remote sensor must be placed outdoors. The remote

sensor will take about 30 minutes to aclimatize to the outdoor environment.

To select the Outdoor temperature , press the “Temp” button until “OUT” appears on the base display.

If there is no temperature reading displayed, continue to press the “Temp” button until the temperature is

displayed together with the “OUT” icon.

Note: Your Thermo DECT supports up to 3 remote sensors. Each one occupies one of 3 channnels.

If you cannot find a remote sensor on one of the 3 channels please go to the section “Searching

for the Remote Sensor”.

Suggestion: Place up to 3 Remote Sensors in important areas of your home such as the Baby’s Room,

Wine Cellar, Greenhouse. Additional remote sensors are sold separately.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oregon Scientific TD339 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oregon Scientific TD339

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info