Bedienungsanleitung Oxford OF690 HotGrips (Seite 2 von 7) (Englisch)

606569

Zoom out

Zoom in

Vorherige Seite

1/7

Nächste Seite

Oxford Hotgrips instructions v.8 switch - 09/07/12

Oxford HotGrips™: Fitting and User Instructions for part codes:

OF690 Adventure, OF691 Touring & OF692 Sports HotGrips™ with v.8 heat controllers.

A: Safety ﬁrst: read carefully before ﬁtting or using!

IMPORTANT: If you have any doubt about ﬁtting your Oxford HotGrips™, immediately consult your local authorised

Oxford stockist for advice or alternatively visit our website www.oxprod.com and check for updates on the Frequently

Asked Questions.

WARNINGS:

i. Your HotGrips must only be connected and turned on when ﬁtted to your handlebars as per the instructions.

ii. Before using the motorcycle/vehicle each time, please ensure that the ﬁtted HotGrips are ﬁrmly glued to the

handlebar. Failure to do so could result in an accident or personal injury.

iii. Ensure that the throttle operates freely. Ensure that normal operation of the motorcycle is not affected. The Hotgrip

cables must not foul or restrict the operation of the brake or clutch levers.

iv. HOTGRIPS are designed for use with gloved hands. Do not allow bare skin to come into contact with your HotGrips

when turned “on”. Check the temperature for suitability before you set off. If the temperature becomes too hot

when on the move, pull over safely and turn the temperature down or turn the switch OFF if appropriate.

v. Do not leave the motorcycle unattended when the HotGrips are turned on. The heat regulation is only controlled by

the motorcyclist turning the heat controller up or down to suit the ambient weather conditions. If the grips are left

turned ON at a high heat setting whilst the motorbike is in a warm garage or in warm ambient conditions, damage

to the HotGrips or motorcycle could occur. Similarly if the Hotgrips are left turned on when ﬁtted inside handlebar

muffs the temperatures may rise beyond a safe point and damage or even risk of ﬁre could occur in the most

extreme situations. These are designed to be used in cold weather with the rider present.

vi. Replace the HotGrips when the pattern of the outer rubber wears away in any one area or the tread pattern

disappears.

vii. Regularly check the integrity of the attachment and materials of your HotGrips.

Do not use if in doubt and consult your local authorised OXFORD stockist.

viii. OXFORD Products will accept no liability for the consequences of grips, which have not been securely ﬁtted. Liability

is limited to the replacement parts of the HotGrips in case of faulty materials or manufacture.

B: Parts list

Before ﬁtting, check that the following parts are included in the kit:

• 1 x Left HotGrip (22mmØ I/D)

• 1 x Right HotGrip (25.6mmØ I/D)

• 1 x Intelligent Heat Controller (code: OFV8) and adhesive pad

• 1 x Universal bracket for switch - OF91 (tment may not be suitable for all vehicles)

• 1 x Wiring loom (1.52mtr long : code OF695L)

• Cable ties and grip superglue

Code/Grip Standard length (mm) Minimum length (mm)

OF690 Adventure 132 122

OF691 Touring 120 110

OF692 Sports 123 114

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oxford OF690 HotGrips Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oxford OF690 HotGrips

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info