Bedienungsanleitung Oxford OF690 HotGrips (Seite 3 von 42) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

606569

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

Oxford Hotgrips instructions v.8 switch - 09/07/12

Tools needed:

• A course and ne le for smoothing the throttle slider tube

• Glass paper for cleaning the handlebars

• Cable snippers or pliers

• Standard motorcycle tools to remove the seat, fairing panels and battery connections

C: Fitting and Wiring Instructions for Motorcycles

Your Oxford HotGrips are designed as a replacement for the handle bar grips already ﬁtted to the motorcycle.

Hotgrips will t onto most motorcycles that use 22mm or 7/8” Ø handlebars. The grip has an open end to allow for

the bar end weight to be reﬁtted without the need to trim the grip. If the end of the Hotgrip does need to be trimmed

to ensure that a bar-end weight can be tted without fouling the Hotgrips, then it is advisable to trim up-to the point

shown in the diagram below. This ensures that the heating elements do not get cut.

The left and right grip are different sizes:

One is designed to t over the left handlebar and has an internal diameter of approximately 22mm.

The other ts over the throttle slider on the right handlebar and has a diameter of approximately 25mm.

D: Fitting Procedure

1. Remove the existing handlebar grips.

2. Clean the left handlebar ensuring that the bars are smooth and free of glue and residue.

3. The bar should measure a consistent 22mm diameter.

4. When the right grip is removed there is a nylon throttle slider underneath. This may need to be removed and any

raised areas smoothed off to ensure that the diameter is a consistent 25.6mm.

This often involves ﬁling off the raised ridges that were formed on the throttle slider.

Trim length here (picture below)

E: Trial ﬁt the Oxford HotGrips

1. Always “dry t” the grip to the bar rst, to ensure that the grip is a snug t before using the adhesive.

2. The HotGrips have a unique internal tube that can expand to t over the handlebar.

3. This makes them easier to t over handlebars that have inconsistent diameter bars due to manufacturing

tolerances.

4. If the grips are too tight to slide on with only gentle effort, do not force them on or damage may occur. Check the

dimensions of the handlebars again and adjust as necessary.

5. If the HotGrips do not slide on easily, check if there is any excess rubber on the inside of the grip which may have

seeped through the expansion slot during manufacturing. If so, use a long ﬁle and gently remove the excess

rubber with the edge of the ﬁle.

6. When sliding the grips onto the handlebars it is possible to twist them into place until they reach the correct

ﬁnished position.

Trim lengths

Trim lengths Trim lengths

OF690 Adventure OF691 Touring OF696 Sports

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oxford OF690 HotGrips Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oxford OF690 HotGrips

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info