Bedienungsanleitung Oxford OF693 HotGrips (Seite 2 von 42) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

606567

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

Oxford HotGrips™: Fitting and User Instructions for part codes OF693 and OF696

with v.7 heat controllers.

A: Safety ﬁ rst: read carefully before ﬁ tting or using!

IMPORTANT: If you have any doubt about ﬁ tting your Oxford HotGrips™, immediately consult your local

authorised Oxford stockist for advice or alternatively visit our website www.oxprod.com and read the

Frequently Asked Questions.

WARNINGS:

i. Your HotGrips must only be connected and turned on when ﬁ tted to your handlebars as per the

instructions.

ii. Before using the motorcycle/vehicle each time, please ensure that the ﬁ tted HotGrips are ﬁ rmly glued

to the handlebar. Failure to do so could result in an accident or personal injury.

iii. Ensure that the throttle operates freely. Ensure that normal operation of the motorcycle is not

affected. The Hotgrip cables must not foul or restrict the operation of the brake or clutch levers.

iv. HOTGRIPS are designed for use with gloved hands. Do not allow bare skin to come into contact with

your HotGrips when turned “on”. Check the temperature for suitability before you set off. If the

temperature becomes too hot when on the move, pull over safely and turn the temperature down or

OFF as appropriate.

v. Do not leave the motorcycle unattended when the HotGrips are turned on. The heat regulation

is only controlled by the motorcyclist turning the heat controller up or down to suit the ambient

weather conditions.

If the grips are left turned ON at a high heat setting whilst the motorbike is in a warm garage or in

warm ambient conditions, damage to the HotGrips or motorcycle could occur. Similarly if the Hotgrips

are left turned on when ﬁ tted inside handlebar muffs the temperatures may rise beyond a safe point

and damage or even risk of ﬁ re could occur in the most extreme situations.

These are designed to be used in cold weather with the rider present.

vi. Replace the HotGrips when the pattern of the outer rubber wears away in any one area.

vii. Regularly check the integrity of the attachment and materials of your HotGrips.

Do not use if in doubt and consult your local authorised OXFORD stockist.

viii. OXFORD Products will accept no liability for the consequences of grips, which have not been securely

ﬁ tted. Liability is limited to the replacement parts of the HotGrips in case of faulty materials or

manufacture.

B: Parts list for product: OF693 and OF696

Before ﬁ tting, check that the following parts are included in the kit:

• 1 x Left HotGrip (22mm I/D x 125mm long )

• 1 x Right HotGrip (25.6mm I/D x 125mm long)

• 1 x Electronic Heat Controller (code OF696HS v7) and adhesive pad

• 1 x Universal bracket for switch - OF91 (ﬁ tment may not be suitable for all vehicles)

• 1 x Wiring loom, cable ties and grip glue

1 Oxford Hotgrips instructions v.7 switch - 10/12/08

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oxford OF693 HotGrips Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Oxford OF693 HotGrips

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info