Bedienungsanleitung Oxford OF772 HotGrips (Seite 5 von 40) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

606572

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

3. Clutch side HotGrips:

• Apply plenty of glue along the length and around the diameter of the handle bar where the grip

will nally sit.

• Push the grip into place ensuring that the HotGrips are positioned correctly so it does not foul the

clutch operation.

4. Throttle side HotGrips:

• If the grip is a very tight t over the throttle slider, then it is advisable to apply plenty of glue on

the actual nylon throttle slider on the inner most ange and less along the length of the throttle

slider. This is to ensure that the grip and glue do not set too early and half way up the throttle

slider. We would also recommend to apply a ring of glue around the outer end of the throttle slider

as some of this will naturally be drawn up the length of the throttle slider tube.

If however the grip slides easily over the throttle slider then we would recommend using plenty

of glue around the whole circumference of the throttle slider to ensure a safe and secure tment.

5. Be sure to act immediately to wipe away any excess glue with a dry cloth.

6. Allow the glue to dry for at least 24 hours before using. Ensure that the grips are rmly xed in place

before use. Do not use if the grip moves and seek advice immediately.

H: Wiring Harness Installation

1. Find a suitable location to panel mount the switch and then take the wiring back to the battery to

ensure it easily reaches. Then unscrew the panel before drilling a hole of approximately 20mm.

In this kit, we provide a 20mm drill bit for making the hole. It will form a hole in most plastic panels.

When drilling, choose a slow drill speed and slowly create the hole. Remember to wear appropriate

safety goggles and clothing.

If you prefer, most motorcycle dealers will be happy to t these Hotgrips for you.

Put the whole wiring loom through the 20mm hole and feed the wiring along the scooter chassis until

the ring leads reach the battery. Push the switch into the hole and ensure it has popped into position

and is retained securely in the panel. Ensure that the waterproof switch cover is wrapped under the

switch and is therefore sealing against the body panel.

2. Remember to install the switch in a suitable position ensuring the wiring harness will reach the wires

from the grips without strain.

3. The loom is designed for ease of tting. There are only 2 wires that need attaching to the scooter’s

existing wiring system. All other connections are through the multi pin block connectors and cannot

be tted the wrong way.

4. A panel mount LED has been included in the wiring loom which can be tted near to the switch if

required. To t this, drill a 6.5 mm diameter hole and push the LED light from the inside of the panel

and it will pop into place.

Oxford Scooter HotGrips Instructions 10/12 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Oxford OF772 HotGrips Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info