ECOMOW
ELECTRIC MOWER
1000W 305mm
ORIGINAL INSTRUCTIONS
SPECIFICA
V
Motor: 1000W
No Load Speed: 3,400/min
Cutting Width: 305mm
Cutting Heights: 3 levels, 30-70mm
Catcher Capacity: 25 litre
Power Cord Length: 10m
Protection Class: II
Weight: 7.97kg
ELM-1030U
WHA
Electric Lawn Mower
Handle Fasteners
Grass Catcher
General safety regulations for this electrical tool
This equipment is not allowed to be used by children. Children should be supervised so that they do not play with the
equipment. Children are not allowed to carry out the cleaning or maintenance. This equipment is not allowed to be used
by people with limited physical, sensory or mental capacities or by those with insufcient knowledge or experience unless
they are supervised or instructed by a person who is responsible for them.
Safety instructions for hand mower
• Before use, check the mains cable and extension cable for signs of damage and aging.
• If the cable is damaged during operation, disconnect it immediately from the power supply
• Check the machine for signs of damage before use. Repairs may only be carried out by our service workshop. If unusual
vibrations occur during use, switch the machine off immediately and pull the plug. Check the cutters and clean them if
necessary
workshop.
• The machine must not be tipped whilst it is being started. Both hands must be on the handle when you start the
machine.
• Worn parts may only be replaced by our service workshop. If necessary contact the service address provided.
W
• Do not use the mower if the connection cable is damaged or worn.
• Do not use a damaged cable to connect the machine to the mains supply and do not touch a damaged cable whilst it is
connected to the mains.
• Do not touch the cutters until the machine has been disconnected from the mains and the cutters have reached a
complete standstill.
• Keep extension cables away from the cutters. The cutters can damage the cables and result in contact with live parts.
• Break the connection with the mains supply (in other words pull the plug out of the socket):
- whenever you leave the machine unattended;
- before released a blocked cutter;
- before inspecting or cleaning and before working on the machine;
- if a foreign body has been struck;
- whenever the machine starts to vibrate oddly
• Carefully read the instructions for how to operate the machine safely
• We recommend that the machine is only connected to a power supply protected by means of an earth
-leakage circuit breaker (RCD) with a maximum trip current of 30 mA.
Note
a) Read the directions with due care. Familiarize yourself with the operator controls and proper operation of the machine.
b) Never allow children or other persons who are not familiar with the operating instructions to use the mower. Contact
your local governmental agency for information regarding minimum age requirements for the user
c) Never mow in the direct vicinity of persons
- especially children
- or animals.
d)
and/or their property
Preliminary measures
a)
-slip footwear and long trousers when mowing. Never mow barefoot or in sandals.
clothing with hanging belts or cords.
b) Check the ground on which the equipment will be used and remove all objects that could be caught up or violently
ung out.
c) Before using the scythe, visually inspect it to ensure that the blade, mounting bolts and the entire cutting apparatus are
in good working order (i.e. not worn out or damaged). T
and mounting bolts as a set only (if applicable). Worn or damaged cutting tools must be replaced.
d) Before use, check the power cable and extension cable for signs of damage and wear
during operation, disconnect it immediately from the power supply
DISCONNECTED. Do not use the equipment if the cable is worn or damaged.
e) Remember that if the machine has several cutting tools, the movement of one cutting tool may result in the other
cutting tools starting to rotate.
Handling
a) Only mow in broad daylight or in well-lit conditions.
b) Do not use the machine on wet grass.
c)
d) Only operate the machine at a walking pace.
e)
f) Be particularly careful when you change direction on a slope.
g) Do not mow on overly steep inclines.
h)
i) Switch the mower off , pull the plug and wait until the cutters have reached a complete standstill if you need to tip the
mower over
to mow
j) Never use the lawn mower if the guards are damaged or without the attached guards, e.g. deectors and/or grass
catching devices.
k) Use the ON/OFF switch carefully as described in the manufacturer’s instructions. Make sure that your feet are far
enough away from the mower blade!
l) The lawn mower should not be tilted when the motor is switch on unless it has to be raised for starting purposes. In this
case, tilt it as little as absolutely necessary and only raise the side opposite to that of the user
m) Do not switch on the mower if you are positioned in front of the chute.
n) Never move your hands or feet toward or under any rotating parts. Keep clear of the chute opening at all times.
o) Never lift or carry a lawn mower with the engine running.
p) Switch off the motor and pull the plug out of the socket. Make sure that all moving parts have reached a complete
standstill:
- before you dislodge any blockages or clogs in the chute.
- before carrying out any checks, cleaning, maintenance or other work on the lawn mower
- if you have struck a foreign object. Examine the mower for signs of damage and carry out any necessary repairs before
restarting and continuing to work with the mower
- if the lawn mower begins to experience exceptionally strong vibrations, immediately switch it off and check it.
- Search for damage.
- Repair the damaged parts as required.
- Make sure that all nuts, bolts and screws are fastened securely
q) Switch off the mower and pull the plug whenever you leave the mower
Maintenance and storage
a) Make sure that all nuts, bolts and screws are tightened securely and that the machine is in safe working condition.
b)
c) T
d) Routinely check the grass basket for signs of wear and impaired functionality
e) For your own safety
f) T
adjusting the equipment.
g) While you are carrying out maintenance work on the cutting tools, remember that the cutting tools can still be moved
even if the power source has been switched off .
h) For your own safety
accessories.
Ozito Industries will not be responsible for any damage or injuries
caused by repair of the tool by an unauthorised person or mishandling
or mistreatment of the tool. This tool is designed for Domestic Home Use
only
CAUTION!: AL
– SHARP EDGES COULD CAUSE SERIOUS INJUR
USE GLOVES.
MAINTENANCE
W BEFORE CLEANING
ELECTRIC MOWER OR CARR
MAINTENANCE PROCEDURE, MAKE SURE THA
MOTOR IS OFF
THE POWER SUPPL
ST
Removing the Blade
1.
blade rmly and with a 13mm socket
(not supplied) loosen the blade bolt
by turning it anti-clockwise.
Note:
holding the blade while removing or
tightening the blade bolt.
2. Remove the blade bolt and blade.
3.
necessary
Replace the metal blade after 50 hours mowing or 2 years whichever is
the sooner – regardless of condition. If the blade is cracked or damaged
replace it with a new one. Never use a blade bolt if the insulated head is
damaged, cracked or missing.
Fitting the Blade
•
working condition.
• Check the catcher frequently for wear or deterioration.
• Replace worn or damaged parts for safety
• Only use the replacement blade, blade bolt, and impeller specied for this
product.
• Be careful during adjustments of the lawn mower to prevent entrapment of
the ngers between moving blade and xed parts of the machine.
•
•
of reach of children.If the housing of the mower requires cleaning, do not use
solvents but a moist soft cloth and brush only
• Frequently check the wheel threads are rm and tight.
CAUTION!: DO NOT TOUCH ROT
ADDITIONAL SAFE
1. Fit the blade to the fan with the tilt edges of the blade facing towards the
mower
2. Re-assemble blade bolt through blade and fan.
3. Hold the blade rmly and tighten blade bolt with a (not supplied), by turning
in a clockwise direction. The tightening torque should be approx. 25 Nm.
ozito-diy.co.uk
OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG
All of our products undergo strict quality checks to ensure that they reach
you in perfect condition. In the unlikely event that your device develops a
fault, please contact our service department at the address shown on this
guarantee card. Y
service number shown. Please note the following terms under which
guarantee claims can be made:
1. These warranty terms regulate additional warranty services, which the
manufacturer mentioned below promises to buyers of its new products
in addition to their statutory guarantee claims are not affected by this
guarantee. Our guarantee is free of charge to you.
2. The warranty services only covers defects due to material or
manufacturing faults on a product which you have bought from the
manufacturer mentioned below are limited to either the rectication of said
defects on the product or the replacement of the product, whichever we
prefer
Please note that our devices are not designed for use in commercial, trade
or professional applications.
device has been used by commercial, trade or industrial business or has
been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly
instructions or due to incorrect installation, a failure to follow the operating
instructions (for example connecting it to an incorrect mains voltage or
current type) or a failure to follow the maintenance and safety instructions
or by exposing the device to abnormal environmental conditions or by lack
of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example
overloading the device or the use or unapproved tools or accessories),
ingress of foreign bodies into the device (such as sand, stones or dust,
transport damage), the use of force or damage caused by external forces
(for example by dropping it).
- Damage to the device or parts of the device caused by normal or natural
wear or tear or by normal use of the device.
4. Y
date of purchase and is intended for DIY (Do It
excludes consumable parts. Guarantee claims should be submitted
before the end of the guarantee period within two weeks of the defect
being noticed. No guarantee claims will be accepted after the end of the
guarantee period. The original guarantee period remains applicable to the
device even if repairs are carried out or parts are replaced. In such cases,
the work performed or parts tted will not result in an extension of the
guarantee period, and no new guarantee will become active for the work
performed or parts tted. This also applies if an on-site service is used.
IN ORDER
RETURN
REGISTER RECEIPT
Please refer to the restrictions of this warranty concerning wearing parts,
consumables and missing parts as set out in the service information in
these operating instructions.
CUSTOMER
GB: 0151 294 4488
IRL: 1850 88271
Ozito-diy
W
0917
SP
Spare parts can be ordered from the Special Orders
Desk at your local Bunnings W
store.
For further information, or any parts visit
www
Great Britain: 0151 294 4488
Ireland: 1850 88271
E-mail: info@ozito-diy
WWhen using mains-powered tools, basic safety precautions, including the
following, should always be followed to reduce risk of re, electric shock, personal injury
and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an emergency
before operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
Before you connect the equipment to the mains supply make sure that the data on the rating plate are
identical to the mains data.
This tool is double insulated therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid
a hazard.
Note: Double insulation does not take the place of normal safety precautions when operating this tool. The
insulation system is for added protection against injury resulting from a possible electrical insulation failure
within the tool.
Using an Extension Lead
Please only use power cables that are not damaged. The total length of the power cable should not exceed
40 meters; going beyond this distance will reduce the power output of the electric motor
must have a cross-section of 3 x 1.5 mm2. The insulating sheath of lawn mower power cables is frequently
damaged.
Some of the causes for this are:
• Cuts caused by running over the cable
• Pinching when the power cable is dragging under doors and pulled through windows.
• Cracking due to old age of the insulation
• Kinking by improperly fastening or guiding the power cable.
The power cables must, at the very minimum, be of type HO5RN-F and 3-stranded. The cable type must
be printed somewhere on the power cable. Only purchase power cables that are marked as such! Plugs
and socket couplers for the power cables must be made from rubber and be splash proof. There is a limit to
how long power cables can be. Longer power cables require larger conductor cross-sections. Power cables
and connecting lines must be regularly checked for damage. Ensure that the lines are de-energized before
checking them. Completely unwind the power cable.
couplers for kinks.
ELECTRICAL SAFE
DESCRIPTION OF SYMBOLS
GENERAL POWER TOOL SAFE
W “Read all safety warnings, instructions, illustrations and specications provided
with this power tool.” Failure to follow the warnings and instructions may result in electric shock,
re and/or serious injury
Save all warnings and instructions for future reference. The term “power tool” in the
warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power
tool.
1. Work area safety
a. . Cluttered or dark areas invite accidents.
b.
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Distractions can cause you to
lose control.
2. Electrical safety
a.
adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
f.
protected supply Use of an RCD reduces the risk of electric shock.
3. Personal safety
a.
not use a power tool while you are tired or under the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury
b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c.
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your
nger on the switch or energising power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A
attached to a rotating part of the power tool may result in personal injury
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f.
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related hazards.
h)
ignore tool safety principles.
4. Power tool use and care
a. The correct power tool
will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c.
the power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools and accessories. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained power
tools.
f. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
5. Service
a.
parts. This will ensure that the safety of the power tool is maintained.
SERVICE INFORMA
Please note that the following parts of this product are subject to normal
or natural wear and that the following parts are therefore also required
for use as consumables.
* Not necessarily included in the scope of delivery!
Category Example
Wear parts* Carbon brushes, V
Consumables* Blade
Missing parts
DECL
Gao/Product-Management
explains the f
the following pr
Electric Lawn Mow
2014/29/EU
2005/32/EC_2009/125/EC
2014/35/EU
2006/28/EC
X
2014/30/EU
2014/32/EU
2014/53/EC
2014/68/EU
90/396/EC_2009/142/EC
89/686/EC_96/58/EC
X
2011/65/EU
X
2006/42/EC
Annex IV
Notied Body:
Notied Body No.:
Reg.
X
2000/14/EC_2005/88/EC
Annex V
X
Annex VI
Noise: measur
WA
= 93 dB (A); guar
WA
= 96 dB (A)
P = 1 KW;
Notied Body: Société Nationale de Certication et DʼHomologation
S.A.R.L.
2012/46/EU
Emission No.:
Standard ref
EN 55014-1;
Landau/Isar
First CE: 17 Archive-File/Record: NAPR017645
Art.-No.: 30.001.97 I.-No.: Documents registrar: R. Gehar
Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar
ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar
3000197_11017_ELM_1030U.indd 135 14.09.2017 11:15:26
For EU countries only
Never place any electric power tools in your household refuse.
T
and electronic equipment and its implementation in national laws, old
electric power tools have to be separated from other waste and disposed
of in an environment-friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to the manufacturer
owner of the electrical equipment must make sure that the equipment is
properly disposed of if he no longer wants to keep the equipment. The old
equipment can be returned to a suitable collection point that will dispose
of the equipment in accordance with the national recycling and waste
disposal regulations. This does not apply to any accessories or aids
without electrical components supplied with the old equipment.
The reprinting or reproduction by any other means, in whole or in part, of
documentation and papers accompanying products is permitted only with
the express consent of the iSC GmbH.
Subject to technical changes.
Danger!
Sound and vibration
Sound and vibration values were measured in accordance
with the standards EN ISO 3744: 1995, EN ISO 1
20643: 2005.
L
pa
at the operator position: 80.4 dB
K
pa
uncertainty: 3 dB
L
wa
sound power level 96 dB
K
wa
uncertainty: 3 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing.
T
accordance with EN 60745.
Vibration at the handles
Vibration emission value a
h
= 2.285 m/s
2
K uncertainty = 1.5 m/s
2
Keep the noise emissions and vibrations to a minimum.
• Only use appliances which are in perfect working order
• Service and clean the appliance regularly
•
• Do not overload the appliance.
• Have the appliance serviced whenever necessary
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Danger! Read the directions f
operating the equipment.
Caution! Keep all other persons awa y from the
danger zone.
Caution! Sharp blades! Pull out the safety plug before
carrying out any repair work or if the pow er cable is
damaged.
is switched off.
Caution! Keep the powwa y from the cutters!
Guaranteed sound pow er lev
Danger! Read the operating instructions to reduce the risk of injury
Protection class II
ADDITIONAL INFORMA
Only replace the blade with a genuine Ozito replacement blade, as this will
ensure top performance and safety under all conditions.
TROUBLESHOOTING
Problem Cause Remedy
The motor
fails to start
The capacitor is
defective
The mower housing is clogged.
Have repaired by the Customer
Service Centre
There is no electricity
at the plug
Check the cable and the fuse
The cable is defective Check the cable
The combined switch/
plug is defective
Have repaired by the Customer
Service Centre
The connectors have
become separated
from the motor or the
capacitor
Have repaired by the Customer
Service Centre
The mower is standing
in high grass
Start in low grass or on an area
that has already been mowed;
change the cutting height if
necessary
Start in low grass or
on an area that has
already been mowed;
change the cutting
height if necessary
Clean the housing so that the
blade moves freely
The motor
performance
drops
The grass is too high
or too damp
Correct the cutting height
The mower housing is
clogged
Clean the housing
The blade is severely
worn
Replace the blade
Cutting is
irregular
The blade is worn Replace or re-sharpen the blade
Wrong cutting height Correct the cutting height
