Bedienungsanleitung P1PE P72800A (Seite 25 von 32) (Englisch)

779805

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

the problem, contact your dealer or the

manufacturer directly. Use only original

parts approved by the manufacturer,

otherwise a hazard risk arises.

ENGINE WILL NOT START

Possible causes;

1. Fuel tank is empty.

2. Fuel tap is in the OFF position.

3. Choke is at the RUN position.

4. Engine switch is in the OFF position.

5. Spark plug dirty/defective.

6. Spark plug wet with fuel (flooded engine).

7. Poor quality fuel; Pressure washer stored

without treating or draining petrol, or refueled

with bad petrol.

8. Low engine oil level.

9. Fuel filter clogged, carburetor malfunction,

ignition malfunction, valves struck, etc.

Possible corrective actions;

1. Refill with clean unleaded petrol.

2. Move fuel tap to ON position.

3. Move choke lever to START position.

4. Turn engine switch to ON position.

5. Check that spark plug wire is connected

properly. Clean or replace spark plug with

properly gapped spark plug.

6. Dry and reinstall spark plug. Start engine with

throttle lever in FAST position.

7. Drain fuel and carburetor and refuel with

fresh petrol. Please contact after sales service

for further assistance.

8. Add engine oil to proper level, see engine

manual.

9. Take engine to your dealer and/or contact

after sales service for instructions.

ENGINE LACKS POWER

Possible causes;

1. Air filter clogged

2. Throttle control is in the slow position

3. Fuel filter clogged, carburetor malfunction,

ignition malfunction, valves struck, etc.

4. Poor quality fuel; Pressure washer stored

without treating or draining petrol, or refueled

with poor quality fuel.

Possible corrective actions;

1. Clean or replace filter.

2. Move throttle control to fast position.

3. Take engine to an authorized servicing

dealer and/or contact after sales service.

4. Drain fuel and carburetor and refuel with

fresh gasoline. Please contact after sales

service for further assistance.

LOW OR SURGING PRESSURE

Possible causes;

1. Insufficient water supply.

2. Blocked inlet screen.

3. Need to use high pressure nozzle.

4. Blocked.

5. Worn nozzle.

6. Leaking high pressure hose.

Possible corrective actions;

1. Increase water flow – check for kinked or

pinched hose.

2. Carefully remove screen and clean.

3. Change to correct nozzles either green,

yellow, white, or red nozzle.

4. Safely remove nozzle as outlined in this

manual and check for blockage.

5. Replace nozzle.

6. Fix leaks if not leaking from hose – NB DO

attempt to repair hose leaks.

NO DETERGENT

Possible causes;

1. Need to use different nozzle.

2. Back pressure from extra-long hose.

3. Leak in clear detergent hose.

4. Detergent strainer not submerged.

5. Detergent strainer blocked.

Possible corrective actions;

1. Change to the BLACK nozzle.

2. Try shorter high pressure hose.

3. Replace hose. Use hose clamps if necessary.

4. Make sure strainer is completely submerged

in solution.

5. Clean detergent strainer.

7. TROUBLESHOOTING

7.1. If troubleshooting does not solve

Page 25

First edition - April 2017

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

P1PE P72800A Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info