Bedienungsanleitung Packard Bell Easy Note LK11BZ (Seite 20 von 24) (Englisch)

470139

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

20 - Quick start guide

The cord length must not exceed 2.5 metres. To prevent electrical hazards, do not remove

or disable the ground contact on the power cord. Replace the power cord if it gets damaged.

Contact your dealer for an exact replacement. In Europe, the plug must be rated for 250

VAC, 10 amp minimum. The plug must display an international agency approval marking.

The cord must be suitable for use in the end-user country. Consult your dealer or the local

electrical authorities if you are unsure of the type of power cord to use in your country.

Cables

For cables which are not delivered with the Product in the computer's packaging:

The EMC performance of the system is guaranteed only if the cable and interface use

efficient shielding.

The use of shielded interface cable is required for USB, IEEE1394, serial, printer, game,

analog or digital audio/ video, PS2, TV or FM antennas, and generally all high-speed

cable interfaces.

Use only UL Listed No. 26AWG or larger telecommunication cords.

Only Ethernet LAN or RTC modem cable can have length exceeding 3 metres.

Packard Bell recommends that you add a ferrite core round clip to each cable connecting

your computer to a hardware device that was not included with your computer.

- Ferrite reference: 28A-2029 from Steward (two loops)

During product certification, Packard Bell used the following cable quality:

- USB2.0 Certified Cables from Hama 46778

- IEEE1394 shielded FireWire from Hama 50011

- RCA-RCA shielded Audio/Video Cables from Thomson KHC001M, KHC012M,

KHC028M

- Stereo Jack shielded Audio cables from Hama 43330H, 42714H

Heat Build-up and Portable Computers

The AC adapter and the underside of the computer can become hot after prolonged use.

Sustained physical contact with either should be avoided.

CHASSIS COVER REMOVAL AND REPLACEMENT

Before removing the chassis cover to service or modify the equipment, you must

disconnect all power and modem cords, and remove or disable the battery.

Caution: Some components inside the computer can become hot after

prolonged use.

You then must close the chassis before you plug in and switch on the equipment.

LASER COMPLIANCE STATEMENT

The optical devices are tested and certified to be compliant with International

Electrotechnical Commission IEC60825-1 and European EN60825-1 standards for Class

1 laser products.

Class 1 laser products are not considered hazardous. The optical devices are designed

such that there is never human access to laser radiation above a Class 1 level during

normal operation or prescribed maintenance conditions.

The optical devices installed in your computer are designed for use solely as components of

such electronic product and therefore do not comply with the appropriate requirements of

Code of Federal Regulation Sec. 1040.10 and Sec. 1040.11 for COMPLETE laser products.

Because exposure to laser radiation is extremely hazardous, under no circumstances

should the user attempt to disassemble the laser device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Packard Bell Easy Note LK11BZ Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Packard Bell Easy Note LK11BZ

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info