Bedienungsanleitung Packard Bell EasyNote DT (Seite 49 von 56) (Englisch)

469052

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Helpdesk - 49

Returning your system to its factory condition

If your computer experiences problems that are not recoverable by other methods, you may need to reinstall everything to

return your system to its factory condition. You can reinstall using either your hard drive or the recovery discs you have

created.

Caution: This complete recovery deletes everything on your hard drive, then reinstalls Windows and all

software and drivers that were pre-installed on your system. If you can access important files on your

hard drive, back them up now.

• If you can still run Windows, see “Recovering from within Windows” below.

• If you cannot run Windows and your original hard drive is still working, see “Recovering from the hard drive during startup”

on page 49.

• If you cannot run Windows and your original hard drive has been completely re-formatted or you have installed a

replacement hard drive, see “Recovering from your recovery discs” on page 49.

Recovering from within Windows

To reinstall Windows and all pre-installed software and drivers:

1. Click on Start > All Programs > Packard Bell, then click on Packard Bell Recovery Management. Packard Bell

Recovery Management opens.

2. Click on the Restore tab, then Restore system to factory default. The Confirm Restoration dialogue box opens.

3. Click on Yes, then Start. A dialogue box displays information about the hard drive that the operating system will be

recovered to.

Caution: Continuing the process will erase all files on your hard drive.

4. Click on OK. The recovery process begins by restarting your computer, then continues by copying files to your hard drive.

This process may take a while, but a Packard Bell Recovery Management screen shows you its progress.

When the recovery has finished, a dialogue box prompts you to restart your computer.

5. Click on OK. Your computer restarts.

6. Follow the on-screen prompts for first-time system setup.

Recovering from the hard drive during startup

To reinstall Windows and all pre-installed software and drivers:

1. Turn on your computer, then press Alt+F10 during startup. Packard Bell Recovery Management opens.

2. Click on Restore system from factory default.

Caution: Continuing the process will erase all files on your hard drive.

3. Click on Next. Your hard drive’s original, factory-loaded contents are recovered. This process will take several minutes.

Recovering from your recovery discs

To reinstall Windows and all pre-installed software and drivers:

1. Turn on your computer, insert the first system recovery disc into your optical disc drive, then restart your computer.

Caution: Continuing the process will erase all files on your hard drive.

2. During startup, press F12 to open the boot menu. The boot menu is where you can select which device to start from, such

as the hard drive or an optical disc.

3. Use your arrow keys to select CDROM/DVD, then press Enter. Windows installs from the recovery disc you inserted.

4. Insert the second recovery disc when prompted, then follow the on-screen prompts to complete the recovery.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Packard Bell EasyNote DT Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Packard Bell EasyNote DT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info