Bedienungsanleitung Panasonic AG-AC160AP (Seite 50 von 110) (Englisch)

597924

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

* The COUNT value is indicated as a 4-digit number.

The COUNT value is incremented each time a new

clip is shot when clip metadata has been loaded

and the recording method has been set to [TYPE2].

The COUNT value can be reset with the following

method. Press the <MENU> button, select [META

DATA]



[CLIP COUNTER RST]



[YES], and push

the OPERATION lever to reset the COUNT value to 1.

Using the counter

Counter display

You can display a counter that indicates how much

time has elapsed during shooting or playback.

Press the <COUNTER> button.

Each time you press the button, the display

changes as follows. (Page 75)

[0:00.00] (<CAMERA> mode only)

Counter value display. Displayed when [TOTAL]*

is selected with the [REC COUNTER] item on

the setup menu [DISPLAY SETUP] screen.

[CLIP 0:00.00]

Displayed when [CLIP]* is selected with the

[REC COUNTER] item on the setup menu

[DISPLAY SETUP] screen.

Values are automatically reset when shooting

is started, and counter values are displayed

for each individual clip.

* The count is not displayed in <PB> mode.

[TC 12:34:56.01]

Time code display (Displays the frame digits

in 24 frames in PH1080/24P and PH720/24P

modes. In 480i/24P mode, the frame digits are

converted into 30 frames.)

[UB 12 34 56 78]

User information

No display:

Data is not displayed.

• To reset the counter value, press the <RESET/

TC SET> button while the counter value is

being displayed.

TC preset mode

Synchronizes the initial time code value during

multi-camera shooting. (Hereafter, the camera used

for synchronization is described as the MASTER

and the camera being synchronized is described

as the SLAVE.)

Connect the TC PRESET IN/OUT terminals

(<VIDEO OUT> terminals) on the two devices

with a pin cable, and turn on the power.



MASTER settings

Check that the MASTER camera is set to

the <CAMERA> mode, and set the [EXT

TC LINK] item on the setup menu [TC/UB

SETUP] screen to [MASTER].

[OUTPUTTING LTC SIGNAL] is displayed on

the screen, and the time code is output from the

TC PRESET IN/OUT terminal (<VIDEO OUT>

terminal).

•

Select the same recording format for the

MASTER and SLAVE cameras, and set the

[TCG] item on the [TC/UB SETUP] screen to

[FREE RUN].

•

To cancel the time code output, press the

<MENU> button.



SLAVE settings

Set the [EXT TC LINK] item on the setup

menu [TC/UB SETUP] screen to [SLAVE].

Press the <COUNTER>-<RESET/TC SET>

button. TCG values will be preset to the TC

values input from the MASTER.

•

The menu screen is closed and [TC LINK OK]

is displayed in the center of the screen.

•

If the TC values cannot be set correctly, [LINK

NG] will be displayed.

•

If the SLAVE camera is set to 24P, set the [TC

MODE] item of the MASTER camera to [NDF].

•

To cancel the [SLAVE] mode, press the

<MENU> button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic AG-AC160AP Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info