Bedienungsanleitung Panasonic AG-HVX 200AP (Seite 87 von 138) (Englisch)

597941

Zoom out

Zoom in

Vorherige Seite

1/138

Nächste Seite

Editing

Dubbing

You can dub clips from a P2 card onto a tape that

has been inserted into the unit.

Only clips recorded in 1080i and 720P formats

can be dubbed. In either case, the image signal is

downconverted, reduced to SQUEEZE size, and

recorded in DV format.

Be aware that you cannot dub clips recorded in

DVCPRO50/DVCPRO/DV format onto a tape.

• Check to see if the tape is in a write-protected

state. (During the dubbing operation, an error

message does not appear.)

• Insert the P2 card and tape into the unit, and set

the MEDIA switch to the TAPE position. (Pages

25 and 29)

• When recording for the purpose of dubbing, it is

recommended that a slightly higher setting (+5 or

so) be used for the DETAIL LEVEL item on the

SCENE FILE screen of the setting menu.

1 Set the unit’s POWER switch to ON.

2 Press the mode button to light up the VCR

lamp.

3 Move the tape forward to the position to

start recording.

• It is convenient to use the End Search (page

75) function.

4 Hold down the mode button (at least 2

seconds).

The DUB lamp now lights, and dubbing mode is

established.

VCR

DUB

MCR

CAMERA

The clips on the P2 card appear as thumbnails

on the LCD screen.

• To set the formats that permit dubbing

1) Press the THUMBNAIL button to close

the thumbnail display, and use the MENU

button to open the menu.

2) Select DUBBING SETUP and then

FORMAT SEL to select the format.

Select the same format as the recording

format shown at the bottom left of the

thumbnail display.

(Since the format of clips for which

standard recording was used at the

variable frame rate is 720P/60P, select

720P/60P using FORMAT SEL.)

Dubbing the contents of P2 cards onto a tape (dubbing mode)

3) Use the MENU button to close the menu,

and press the THUMBNAIL button to return

to the thumbnail display.

Clips with formats that permit dubbing are

indicated by black numbers; all other clips

are indicated by the red numbers. (Clips

indicated by the red numbers cannot be

dubbed.)

• To perform the pulldown setting when

dubbing 720/24PA format clips

1) Press the THUMBNAIL button to close

the thumbnail display, and use the MENU

button to open the menu.

2) Select DUBBING SETUP and then

PULLDOWN SEL. Select 24P or 24PA.

24P: 2:3 pulldown

24PA: 2:3:3:2 pulldown

3) Use the MENU button to close the menu,

and press the THUMBNAIL button to return

to the thumbnail display.

5 Select the first clip to be dubbed using the

and buttons, and press the button.

You can select multiple clips by repeating

the above procedure. Upon completing the

selection, switch to the SELECTED CLIPS

display on the THUMBNAIL menu, and check

that the cursor appears at the first clip on the

thumbnail display.

• To dub all the clips in the format selected

in step 4

Position the cursor at the first valid clip

(indicated by the black number) on the

thumbnail display.

• Dubbing will start from the clip where the

cursor is positioned so check the position of

the cursor before proceeding.

• Dubbing will not start if the cursor is

positioned on a clip indicated by a red

number.

(Continued on the next page)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic AG-HVX 200AP Seite 87

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info