Bedienungsanleitung Panasonic AJ-HDC27HP (Seite 134 von 140) (Englisch)

99989

134

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

134

Inspections prior to shooting (continued)

Inspecting the aperture and

zoom functions

Inspecting the VTR unit

Set the zoom to the motorized zoom mode, and

check its operations in this mode.

Check that the image changes when the zoom is

set to the telephoto and wide-angle positions.

1. Tape travel inspection

Set the VTR SAVE/STBY switch to SAVE, and

check that the VTR SAVE lamp inside the

viewfinder lights.

Set the VTR SAVE/STBY switch to STBY, and

check that the VTR SAVE lamp goes off.

Set the TCG switch to R-RUN.

Set the DISPLAY switch to CTL.

Press the unit’s VTR START button, and check

that:

O The tape reels rotate.

O The figure shown on the counter display

changes.

O The REC lamp inside the viewfinder lights.

O The RF and SERVO displays do not appear in

the display window.

Press the unit’s VTR START button again. Check

that the tape stops and the REC lamp inside the

viewfinder goes off.

Use the lens VTR button to check the same

operations as in steps 5 and 6.

Press the RESET button, and check that

“00:00:00:00” appears on the counter display.

Set the LIGHT switch to ON, and check that the

display window illuminates.

Press the REW button, and after the tape has

been rewound for a few seconds, press the

PLAY/PAUSE button.

Check that the tape is recorded, played back

and rewound properly.

Press the FF button, and check that the tape is

fast forwarded properly.

Set the zoom to the manual zoom mode, and

check its operations in this mode.

Turn the manual zoom lever, and check that the

image changes when the zoom is set to the

telephoto and wide-angle positions.

Set the aperture to the auto adjustment mode,

point the lens at some objects with different

brightness levels, and check that the auto aperture

adjustment works.

Set the aperture to the manual adjustment mode,

turn the aperture ring, and check that the manual

aperture is adjusted.

While holding down the auto instantaneous

aperture adjustment button, point the lens at some

objects with different brightness levels, and check

that the auto instantaneous aperture adjustment

function works.

Return the aperture to the auto adjustment mode,

switch the GAIN switch setting to L, M and H, and

check that:

O The aperture is adjusted for objects of the same

brightness level in tandem with the switching of

the gain setting.

O The gain displayed on the viewfinder screen is

switched in tandem with the switching of the

gain setting.

When a lens with an extender has been installed,

set the extender to the operating position, and

check that it works properly.

Perform all the steps outlined in section “1. Tape

travel inspection” through section “4. Earphone and

speaker inspection” one after the other.

04. 英(P128-表４/140) 05.5.18 10:45 ページ134

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic AJ-HDC27HP Seite 134

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info