99987
80
Zoom out
Zoom in
Vorherige Seite
1/134
Nächste Seite
80
Chapter 5 Preparation
5-1 Supplying the power
A battery pack or an external DC power supply can be used
as this unit’s power supply.
To use the battery pack, there is the following
choice of makes of batteries:
Anton/Bauer
IDX
PACO
Sony
Types of battery can be confirmed and revised in the
viewfinder or the menu screen on the monitor.
Press the MODE CHECK button on the side panel of the
unit to display the type of the battery currently set at the top
right of the viewfinder screen.
Using the menu operation, open the <BATTERY/TYPE>
screen from the VTR MENU page to confirm/change it in
the BATTERY SELECT item.
<Notes>
Batteries of other makes can also be supported by
changing the setting menu but no guarantees are made for
the system when they are actually used with this unit.
Before using the battery pack, recharge the battery using
the battery charger.
(For details on the recharging method, refer to the
operating instructions of the battery concerned.)
5-1-1 Attaching the battery and setting the
battery type
Using the Anton/Bauer battery pack
1
Attach the battery pack made by Anton/Bauer.
2
Insert the battery pack and slide it in the direction of the
arrow.
Battery pack made
by Anton/Bauer
<Reference>
A battery holder made by Anton/Bauer is equipped with a
power output connector for the lighting and a lighting control
switch to enable a light to be easily attached. For details on
the lighting systems available, contact Anton/Bauer.
3
Set the battery type.
Select the battery type using the BATTERY SELECT
menu item. This item is selected from the
<BATTERY/TAPE> screen on the VTR FUNCTION
page.
For details, refer to “7-8-3 BATTERY SETTING1.”
Anton/Bauer batteries which can be used
O PROPAC14
O TRIMPAC14
O HYTRON50
O HYTRON100
O HYTRON120
O DIONIC90
O DIONIC100
O DIONIC160
<Reference>
To remove the battery pack, slide it in the opposite direction
to the one in which it was attached while keeping the release
lever on the battery holder pulled down all the way.
Release lever
#
< BATTERY/TAPE >
BATTERY SELECT :DIONIC
EXT DC IN SELECT :AC-ADPT
BATT NEAR END ALARM :OFF
BATT NEAR END CANCEL:ON
BATT END ALARM :ON
BATT REMAIN FULL :70%
TAPE NEAR END ALARM :ON
TAPE NEAR END TIME :2min
TAPE END ALARM :ON
TAPE REMAIN/ :3min/
Power output connector for lighting
Lighting control
switch
01.AJ-HDX900_P_E(VQT0X86)_E 06.6.27 10:09 AM ページ80
80

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Panasonic AJ-HDX900 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info