Bedienungsanleitung Panasonic AJ-HPX 2700G (Seite 150 von 206) (Englisch)

597944

150

Zoom out

Zoom in

Vorherige Seite

1/206

Nächste Seite

150

Maintenance and Inspections: Maintenance

6. Inspection of the clock, time code, and user

bits

1 Set the user bits as required.

Please refer to [Setting of the user bits] (page 62) for the

setting procedures.

2 Set the time code.

Please refer to [Setting the Time Code] (page 66) for the

setting procedures.

3 Set the TCG switch to [R-RUN].

4 Press the REC START/STOP button.

Check that the counter display number changes as

recording progresses.

5 Press the REC START/STOP button again.

Check that recording stops and the counter display

number stops changing.

6 Set the TCG switch to [F-RUN].

Check that the counter display number changes

regardless of recording status.

7 Set the DISPLAY switch to [UB].

Each time the HOLD button is pressed, make sure that

the displayed value changes in the following sequence:

VTCG  DATE  TIME  No display (time zone) 

TCG; and also verify that the displayed value is correct.

If DATE, TIME, or time zone is not correct, refer to

[Setting the Internal Clock’s Date and Time] (page 65)

for guidance on setting the correct values.

Note

Note that date and time data set for DATE, TIME, and

time zone is recorded in clips, and affects the playback

sequence, etc. at the time of thumbnail manipulations.

 Do not use thinner or other solvents to remove dirt.

 Wipe the lens with a commercially available lens cleaner.

 Do not wipe the mirror. If dirt or rubbish is sticking on the

mirror, remove it with a commercially available air blower.

Smears

Smears may appear when shooting an object with very high

brightness.

This phenomenon becomes more obvious as the electronic

shutter speed becomes faster.

White defects

When the frame rate is set low during operation under VFR,

tiny defects may be seen in the video. White defects become

more noticeable in high-temperature operating conditions.

The camera is shipped from the factory with a backup

battery already mounted.

When the battery runs out, the “BACKUP BATT EMPTY”

display appears on the viewfinder screen for 5 seconds after

the POWER switch is turned [ON].

The internal clock stops operating when the battery runs out.

Also, the TCG time code value returns to “00:00:00:00”, and

the time code backup is disabled. The battery must be

replaced.

Please consult your distributor for replacement with a new

battery (CR2032).

The backup battery is visible when the panel on the LCD

monitor side is removed (right side when viewed from the

front).

Maintenance

Cleaning Inside the Viewfinder

Phenomenon Inherent to CCD Cameras

Replacing the Backup Battery

Note

Please contact the store where you purchased the camera

when replacing the battery.

AJ-HPX2700G-VQT1V27_eng.book 150 ページ２００８年９月２日　火曜日　午後５時４３分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic AJ-HPX 2700G Seite 150

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info